33229A
1.INSTALL NO. 1 RELEASE ARM
Install the No. 1 release arm and shift arm pivot to the interlock bracket.
Install a new E-ring to the shift arm pivot.
33245G
2.INSTALL NO. 4 GEAR SHIFT FORK SHAFT
Install the compression spring and shift detent ball to the shift interlock bracket.
Install the No. 4 gear shift fork shaft.
33215B
3.INSTALL NO. 4 GEAR SHIFT FORK
Install the No. 4 gear shift fork to the No. 4 gear shift fork shaft.
Using a 5 mm pin punch and hammer, tap a new slotted spring pin into the No. 4 gear shift fork and No. 4 gear shift fork shaft.
0 to 0.5 mm (0 to 0.0196 in.)
33212A
4.INSTALL NO. 1 GEAR SHIFT FORK
Install the No. 1 gear shift fork and No. 2 gear shift head to the No. 4 gear shift fork shaft.
Using a 5 mm pin punch and hammer, tap a new slotted spring pin into the No. 2 gear shift head and No. 4 gear shift fork shaft.
0 to 0.5 mm (0 to 0.0196 in.)
33242
5.INSTALL NO. 1 GEAR SHIFT FORK SHAFT
Install the compression spring and shift detent ball to the shift interlock bracket.
Install the No. 1 gear shift fork shaft to the shift interlock bracket.
33232F
6.INSTALL NO. 1 GEAR SHIFT HEAD
Install the No. 1 gear shift head to the No. 1 gear shift fork shaft.
Using a 5 mm pin punch and hammer, tap a new slotted spring pin into the No. 1 gear shift head and No. 1 gear shift fork shaft.
0 to 0.5 mm (0 to 0.0196 in.)
33243A
7.INSTALL NO. 2 GEAR SHIFT FORK SHAFT
Install the compression spring and shift detent +ball to the shift interlock bracket.
Install the No. 2 gear shift fork shaft to the shift interlock bracket.
33213G
8.INSTALL NO. 2 GEAR SHIFT FORK
Install the No. 2 gear shift fork with a new bolt.
33244D
9.INSTALL NO. 3 GEAR SHIFT FORK SHAFT
Install the compression spring and shift detent ball to the shift interlock bracket.
Install the No. 3 gear shift fork shaft to the shift interlock bracket.
33214G
10.INSTALL NO. 3 GEAR SHIFT FORK
Install the No. 3 gear shift fork with a new bolt.
33112H
11.INSTALL TRANSMISSION CASE NEEDLE BEARING
Using SST, install the transmission case needle bearing into the front transmission case so that dimension A in the illustration is as specified.
0.50 to 1.50 mm (0.0197 to 0.0590 in.)
| *a | Front |
33111Q
12.INSTALL TRANSMISSION CASE OIL SEAL
Using SST and a hammer, tap a new transmission case oil seal into the front transmission case so that dimension A in the illustration is as specified.
60.0 to 60.8 mm (2.363 to 2.393 in.)
Apply gear oil to the lip of the transmission case oil seal.
33311G
13.INSTALL FRONT BEARING SHAFT SNAP RING
Using snap ring pliers, install the 2 front bearing shaft snap rings.
33124L
14.INSTALL NO. 3 OIL RECEIVER PIPE
Install the No. 3 oil receiver pipe to the front transmission case.
Align the protrusion of the No. 3 oil receiver pipe with the cutout of the front transmission case and install the No. 3 oil receiver pipe to the front transmission case.
33111
15.INSTALL FRONT TRANSMISSION CASE
Apply gear oil to all sliding and rotating parts.
Temporarily install the output shaft assembly, input shaft assembly, counter gear assembly shift interlock bracket, gear shift forks, gear shift fork shafts, and tie them with a piece of rope or string.
Using a snap ring expander, expand the 2 snap rings and install the output shaft assembly, input shaft assembly, counter gear assembly shift interlock bracket, gear shift forks, gear shift fork shafts.
Make sure that the snap ring fits into the grooves of the input shaft and front bearing of the counter gear shaft.
Untie the output shaft assembly, input shaft assembly, counter gear assembly shift interlock bracket, gear shift forks, gear shift fork shafts.
Using a 27 mm hexagon wrench, install a new manual transmission case plug to the front transmission case.
Install the shift interlock bracket with the 4 bolts.
33461
16.INSTALL REVERSE IDLER GEAR
Install the reverse idler gear, reverse idler gear bearing and reverse idler gear shaft.
| *a | 15° |
Make sure that the reverse idler gear faces the correct direction as shown in the illustration.
Make sure that the hole in the reverse idler gear shaft is in the position shown in the illustration.
84210
17.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY
Using SST, install a new gasket and the back-up light switch assembly to the front transmission case.
33251
18.INSTALL SHIFT AND SELECT LEVER
Install the compression spring and lock ball pin to the shift and select lever.
Install the shift and select lever, shift and select cam and shift interlock plate to the shift and select lever shaft.
Using a 5 mm pin punch and hammer, tap in a new slotted pin to the shift and select lever shaft.
1.0 to 2.0 mm (0.0394 to 0.0787 in.)
Install a new bolt to the shift and select lever.
Install a new E-ring to the lever shaft.
33261C
19.INSTALL SHIFT AND SELECT LEVER SHAFT
Align the groove of the shift and select cam with the reverse idler shaft and the claw with the groove of the control assembly, and then install the shift and select lever shaft.
33124D
20.INSTALL NO. 2 OIL RECEIVER PIPE
Install the No. 2 oil receiver pipe to the transmission middle case.
33104
21.INSTALL DRAIN PLUG SUB-ASSEMBLY
Install a new gasket and the drain plug sub-assembly to the transmission middle case.
33101
22.INSTALL TRANSMISSION MIDDLE CASE
Apply seal packing to the transmission middle case as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
| *1 | Seal Packing |
Parts must be assembled within 10 minutes of application. Otherwise, the seal packing (FIPG material) must be removed and reapplied.
Install the transmission middle case to the front transmission case with the 11 bolts.
for bolt A: 40 mm (1.57 in.)
for bolt B: 80 mm (3.15 in.)
33451H
23.INSTALL REVERSE IDLER GEAR SHAFT BOLT
Install a new gasket and the reverse idler gear shaft bolt to the reverse idler gear shaft.
33176B
24.INSTALL TRANSMISSION OIL SEPARATOR
Install the transmission oil separator with the 2 bolts.
36117Q
25.INSTALL TRANSFER ADAPTER NEEDLE ROLLER BEARING
Using SST, install the transfer adapter needle roller bearing to the transfer adapter.
| *a | Front |
33421G
26.INSTALL COUNTER GEAR REAR RADIAL BALL BEARING
Coat a new counter gear rear radial ball bearing with gear oil, and then using SST and a press, install it to the transfer adapter.
Install the bearing lock plate with the bolt.
33321A
27.INSTALL REAR OUTPUT SHAFT BEARING
Using SST and a press, press in 2 new rear output shaft bearings (outer race) to the transfer adapter.
36867B
28.INSTALL OIL SEPARATOR PACKING SEAL
Install the oil separator packing seal to the transfer adapter.
Insert the protruding part of the oil separator packing seal into the groove of the transfer adapter.
33124C
29.INSTALL NO. 1 OIL RECEIVER PIPE
Install the No. 1 oil receiver pipe to the transfer adapter.
36117G
30.INSTALL TRANSFER ADAPTER CASE PLUG
Using a 14 mm hexagon socket wrench, install a new transfer adapter case plug to the transfer adapter.
33101A
31.INSTALL MANUAL TRANSMISSION FILLER PLUG
Install 2 new gaskets and the 2 manual transmission filler plugs to the transfer adapter.
36117
32.INSTALL TRANSFER ADAPTER
Apply seal packing to the transfer adapter as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
| *a | Seal Packing |
Parts must be assembled within 10 minutes of application. Otherwise, the seal packing (FIPG material) must be removed and reapplied.
Install the transfer adapter and 4 brackets to the transmission middle case with the 10 bolts.
33275F
33.INSTALL SHIFT DETENT BALL PLUG
Install the ball and compression spring to the transfer adapter.
Using a 10 mm hexagon socket wrench, install a new shift detent ball plug to the transfer adapter.
33321G
34.INSTALL MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT
Using a belt and wooden block, securely fasten the transmission to the workbench.
Install a new output shaft spacer and a new rear output shaft bearing (inner race).
Temporarily install a new manual transmission output shaft rear set nut by hand.
| *1 | Output Shaft Spacer |
| *2 | Rear Output Shaft Bearing |
| *3 | Manual Transmission Output Shaft Rear Set Nut |
Fit the spacer and rear output shaft bearing securely.
Move the shift and select lever shaft to N.
Using SST, rotate the output shaft 15 times at a speed of 100 rpm or less in order to settle the bearing.
Using SST and a torque wrench, measure the output shaft preload.*1
Engage 5th gear, and then secure the input shaft using SST.
| *1 | Input Shaft |
Install SST securely so that (A) is in-line with the input shaft.
Make sure that (A) moves back and forth by hand after installing SST.
Using SST and a torque wrench, tighten the nut.
Move the shift and select lever shaft to N.
Using SST, rotate the output shaft 15 times at a speed of 100 rpm or less in order to settle the bearing.
Using SST and a torque wrench, measure the output shaft preload.*2
Adjust the preload so that the difference between *1 and *2 is within the specified range.
*2 - *1 = 0.45 to 1.05 N*m (4.59 to 10.7 kgf*cm, 3.99 to 9.29 in.*lbf)
If the preload is more than the standard, replace the output shaft spacer.
Using a chisel and hammer, caulk the manual transmission output shaft rear set nut.
33121G
35.INSTALL MANUAL TRANSMISSION CASE COVER
Apply seal packing to the manual transmission case cover as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
| *1 | Seal Packing |
Parts must be assembled within 10 minutes of application. Otherwise, the seal packing (FIPG material) must be removed and reapplied.
Install the manual transmission case cover with 4 new bolts.
33521
36.INSTALL SHIFT LEVER HOUSING
Install the shift lever housing with a new bolt.
33506F
37.INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY
Apply seal packing to the floor shift control shift lever retainer sub-assembly as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
| *a | Seal Packing |
Parts must be assembled within 10 minutes of application. Otherwise, the seal packing (FIPG material) must be removed and reapplied.
Install the floor shift control shift lever retainer sub-assembly with the 4 bolts.
31204
38.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY