Home › Drivetrain › R150F (MANUAL TRANSMISSION / TRANSAXLE) › OUTPUT SHAFT
RM27T0E _52 Drivetrain _053702 R150F MANUAL TRANSMISSION / TRANSAXLE _0260833 OUTPUT SHAFT A

R150F MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  REASSEMBLY  


PROCEDURE

Hide 33364 1.INSTALL NO. 2 TRANSMISSION HUB SLEEVE

a.
D033571

Install the 3 No. 2 synchromesh shifting key springs and 3 synchromesh shifting keys to the No. 2 clutch hub.

NOTICE:

Make sure that the No. 2 hub sleeve and No. 2 clutch hub are installed facing the proper directions.



b.

Apply gear oil to the sliding part of the No. 2 hub sleeve, and install it to the No. 2 clutch hub.


Hide 33333A 2.INSTALL 3RD GEAR NEEDLE ROLLER BEARING

a.
C089845

Apply gear oil to the needle roller bearing and install it to the output shaft.


Hide 33333 3.INSTALL 3RD GEAR

a.
D026080

Apply gear oil to the 3rd gear and install it to the output shaft.


Hide 33368 4.INSTALL NO. 2 SYNCHRONIZER RING (for 3rd Gear)

a.
D026081

Apply gear oil to the No. 2 synchronizer ring and install it to the 3rd gear.


Hide 33362 5.INSTALL NO. 2 TRANSMISSION CLUTCH HUB

a.
D026082E02
2.26,0.594 1.969,0.594 false 2.313,0.479 2.625,0.688 0.313,0.208 10 false SST

Using SST and a press, install the No. 2 clutch hub to the output shaft.

SST
09608-06041  

NOTICE:
·

Install the hub while aligning the positions of the shifting keys with the key grooves of the No. 2 synchronizer ring.

·

Make sure the 3rd gear rotates smoothly.




b.

Select a snap ring that makes the clearance between the No. 2 clutch hub and snap ring within the specification.

Standard clearance:

0.10 mm (0.00394 in.) or less


Snap Ring Thickness:
Thickness
1.80 mm (0.0709 in.)
1.85 mm (0.0728 in.)
1.90 mm (0.0748 in.)
1.95 mm (0.0768 in.)
2.00 mm (0.0787 in.)
2.05 mm (0.0807 in.)
2.10 mm (0.0827 in.)



c.
D026059

Using a snap ring expander, install the snap ring.

NOTICE:

Do not damage the sliding surface of the bearing.



Hide 33332B 6.INSTALL 2ND GEAR NEEDLE ROLLER BEARING

a.
C089844

Apply gear oil to the needle roller bearing, and install it to the output shaft.


Hide 33332 7.INSTALL 2ND GEAR

a.
D026084

Apply gear oil to the 2nd gear and install it to the output shaft.


Hide 33037B 8.INSTALL NO. 1 SYNCHRONIZER RING SET (for 2nd Gear)

a.
D029127

Apply gear oil to the No. 1 synchronizer ring set and install it to the 2nd gear.


Hide 33331 9.INSTALL REVERSE GEAR

a.
D026083

Using a screwdriver, install the 3 synchromesh shifting key springs and 3 No. 1 synchromesh shifting keys to the No. 1 clutch hub.


b.

Apply gear oil to the reverse gear and install it to the No. 1 clutch hub.


Hide 33361 10.INSTALL NO. 1 TRANSMISSION CLUTCH HUB

a.
C216010E01
0.753,2.84 1.045,2.996 0.292,0.156 10 SST 1.175,2.925 2.345,2.925 false

Using SST and a press, install the No. 1 clutch hub to the output shaft.

SST
09316-60011  (09316-00041)

NOTICE:
·

Make sure that the No. 1 synchromesh shifting key positions are aligned with the No. 1 synchronizer ring key grooves.

·

Make sure the 1st gear rotates freely.




b.

Select a snap ring that makes the thrust clearance between the No. 1 clutch hub and snap ring to be within the specification.

Standard clearance:

0.1 mm (0.00394 in.) or less


NOTICE:

Do not damage the journal surface of the snap ring.


Snap Ring Thickness:
Thickness
2.30 mm (0.0906 in.)
2.35 mm (0.0925 in.)
2.40 mm (0.0945 in.)
2.45 mm (0.0965 in.)
2.50 mm (0.0984 in.)
2.55 mm (0.1004 in.)
2.60 mm (0.1024 in.)



c.
D026087

Using a brass bar and hammer, tap on the snap ring.


Hide 33335B 11.INSTALL 1ST GEAR BEARING SPACER

a.
C089843

Apply gear oil to the bearing spacer and install it to the output shaft.


Hide 33335C 12.INSTALL 1ST GEAR NEEDLE ROLLER BEARING

a.
C089842

Apply gear oil to the needle roller bearing and install it to the output shaft.


Hide 33348A 13.INSTALL 1ST GEAR THRUST WASHER PIN

a.
D026052

Install the thrust washer pin to the output shaft.


Hide 33037B 14.INSTALL NO. 1 SYNCHRONIZER RING SET (for 1st Gear)

a.
C216216

Apply gear oil to the No. 1 synchronizer ring set and install it to the output shaft.


Hide 33335 15.INSTALL 1ST GEAR

a.
D026089

Apply gear oil to the 1st gear and install it to the output shaft.


Hide 33348 16.INSTALL 1ST GEAR THRUST WASHER

a.
D026090

Apply gear oil to the thrust washer and install it to the output shaft.


Hide 33321V 17.INSTALL OUTPUT SHAFT CENTER BEARING

a.
D026091E06
2.24,1.708 2.698,1.292 false 2.729,1.167 3.063,1.344 0.333,0.177 10 false SST

Using SST and a press, install a new center bearing to the output shaft.

SST
09316-60011  (09316-00031)

NOTICE:

Install the center bearing so that the snap ring groove of the bearing faces the rear side.



Hide 33336 18.INSTALL 5TH GEAR

a.
C216011E01
1.981,0.95 2.284,1.098 0.303,0.148 10 SST 1.108,1.622 1.717,1.046 false 1.717,1.046 1.932,1.046 false

Using SST and a press, install the 5th gear to the output shaft.

SST
09316-60011  (09316-00031)

NOTICE:
·

Check that the 5th gear and the splines of the output shaft fit before installing the 5th gear.

·

Make sure face the convex part of the gear faces the front side.