33101A
1.REMOVE MANUAL TRANSMISSION FILLER PLUG
Remove the manual transmission filler plug and gasket from the manual transmission case.
33104
2.REMOVE DRAIN PLUG
Remove the drain plug and gasket from the manual transmission case.
31204
3.REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY
31230
4.REMOVE CLUTCH RELEASE BEARING ASSEMBLY
31236B
5.REMOVE RELEASE FORK SUPPORT
Remove the release fork support from the clutch housing.
31126
6.REMOVE CLUTCH RELEASE FORK BOOT
Remove the clutch release fork boot from the clutch housing.
31111
7.REMOVE CLUTCH HOUSING
Remove the 9 bolts.
Using a plastic-faced hammer, tap off the clutch housing from the manual transmission case.
84210
8.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY
Using SST, remove the back-up light switch assembly and gasket from the manual transmission case.
9.REMOVE RESTRICT PIN
Remove the 2 restrict pins from the transfer adapter.
33506F
10.REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY
Remove the 4 bolts and floor shift control shift lever retainer sub-assembly.
Remove the gasket.
36117
11.REMOVE TRANSFER ADAPTER
Remove the 10 bolts.
Using a brass bar and hammer, tap off the transfer adapter from the manual transmission case.
33124E
12.REMOVE TRANSFER OIL RECEIVER PIPE
Remove the transfer oil receiver pipe from the transfer adapter.
33251
13.REMOVE SHIFT AND SELECT LEVER
Remove the bolt from the shift lever housing.
Remove the shift and select lever and shift lever housing from the transfer adapter.
| *1 | Shift Lever Housing |
| *2 | Shift and Select Lever |
33280
14.REMOVE REVERSE RESTRICT PIN ASSEMBLY
Using a T40 "TORX" socket wrench, remove the reverse restrict pin plug.
Using a 5 mm pin punch and hammer, tap out the reverse restrict pin slotted spring pin.
Remove the reverse restrict pin assembly.
36117A
15.REMOVE TRANSFER ADAPTER OIL SEAL
Using a screwdriver and hammer, tap out the transfer adapter oil seal from the transfer adapter.
33131
16.REMOVE FRONT BEARING RETAINER
Remove the 8 bolts.
Using a brass bar and hammer, tap off the front bearing retainer from the manual transmission case.
33131A
17.REMOVE TRANSMISSION FRONT BEARING RETAINER OIL SEAL
Secure the front bearing retainer in a vise between aluminum plates.
Using SST, tap out the transmission front bearing retainer oil seal.
33311B
18.REMOVE FRONT BEARING SHAFT SNAP RING
Using a snap ring expander, remove the front bearing shaft snap ring from the input shaft front bearing.
33411D
19.REMOVE FRONT NO. 1 COUNTER GEAR BEARING SNAP RING
Using a snap ring expander, remove the front No. 1 counter bearing snap ring from the front counter gear bearing.
33111
20.REMOVE MANUAL TRANSMISSION CASE
Using a brass bar and hammer, tap off the manual transmission case from the intermediate plate.
33449B
21.REMOVE TRANSMISSION MAGNET
Remove the transmission magnet from the intermediate plate.
22.FIX INTERMEDIATE PLATE
Secure the intermediate plate in a vise between aluminum plates.
33275
23.REMOVE NO. 1 SHIFT DETENT BALL SPRING SEAT
for Type A:
Using a 6 mm hexagon socket wrench, remove the No. 1 shift detent ball spring seat from the intermediate plate.
for Type B:
Using a T40 "TORX" socket wrench, remove the No. 1 shift detent ball spring seat from the intermediate plate.
Using a magnet hand, remove the compression spring and detent ball from the intermediate plate.
for Type A:
Using a 6 mm hexagon socket wrench, remove the 2 No. 1 shift detent ball spring seats from the intermediate plate.
for Type B:
Using a T40 "TORX" socket wrench, remove the 2 No. 1 shift detent ball spring seats from the intermediate plate.
Using a magnet hand, remove the 2 compression springs and 2 detent balls from the intermediate plate.
33243A
24.REMOVE NO. 2 GEAR SHIFT FORK SHAFT
Using 2 screwdrivers and a hammer, tap off the snap ring from the No. 2 gear shift fork shaft.
Use a piece of cloth to prevent the snap ring from flying off.
Remove the bolt from the No. 2 shift fork.
Remove the No. 2 gear shift fork shaft from the intermediate plate.
Remove the No. 2 shift fork from the No. 2 transmission hub sleeve.
Using a magnet hand, remove the No. 1 shift interlock roller and shift interlock pin from the intermediate plate.
33242
25.REMOVE NO. 1 GEAR SHIFT FORK SHAFT
Using 2 screwdrivers and a hammer, tap off the snap ring from the No. 1 gear shift fork shaft.
Use a piece of cloth to prevent the snap ring from flying off.
Remove the bolt from the No. 1 shift fork.
Remove the No. 1 gear shift fork shaft from the intermediate plate.
Remove the No. 1 shift fork from the reverse gear.
33244D
26.REMOVE NO. 3 GEAR SHIFT FORK SHAFT
Using a 5 mm pin punch and hammer, tap out the shift fork set slotted spring pin from the No. 3 shift fork.
Using 2 screwdrivers and a hammer, tap off the snap ring from the No. 3 gear shift fork shaft.
Use a piece of cloth to prevent the snap ring from flying off.
Using a magnet hand, remove the straight pin from the reverse shift fork.
Remove the No. 3 shift fork and No. 3 gear shift fork shaft from the intermediate plate.
Using a magnet hand, remove the No. 1 shift interlock roller from the intermediate plate.
33211
27.REMOVE REVERSE SHIFT FORK
Remove the reverse shift fork from the reverse shift arm.
33228
28.REMOVE REVERSE SHIFT ARM BRACKET
Remove the torsion spring from the reverse shift arm bracket.
Remove the 2 bolts and reverse shift arm bracket from the intermediate plate.
Using a screwdriver, pry out the snap ring from the reverse shift arm bracket.
Remove the reverse shift arm from the reverse shift arm bracket.
33321B
29.REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING (for Rear Bearing Side)
Using 2 screwdrivers and a hammer, tap off the output shaft bearing shaft snap ring from the output shaft rear bearing.
Use a piece of cloth to prevent the snap ring from flying off.
33321A
30.REMOVE OUTPUT SHAFT REAR BEARING
Using SST, remove the output shaft rear bearing and output shaft spacer from the output shaft.
| *a | Hold |
| *b | Turn |
31.INSPECT COUNTER 5TH GEAR THRUST CLEARANCE
Using a feeler gauge, measure the thrust clearance.
0.10 to 0.35 mm (0.00394 to 0.0137 in.)
If the clearance is not as specified, replace the counter 5th gear.
32.INSPECT COUNTER 5TH GEAR RADIAL CLEARANCE
Using a dial indicator, measure the radial clearance.
0.015 to 0.068 mm (0.000591 to 0.00267 in.)
If the clearance is not as specified, replace the counter 5th gear bearing with a new one.
33421R
33.REMOVE COUNTER GEAR REAR SHAFT SNAP RING
Using 2 screwdrivers and a hammer, tap off the counter gear rear shaft snap ring from the counter gear.
Use a piece of cloth to prevent the counter gear rear shaft snap ring from flying off.
33395
34.REMOVE NO. 3 TRANSMISSION HUB SLEEVE
Remove the No. 3 transmission hub sleeve from the counter 5th gear.
33318
35.REMOVE NO. 5 GEAR SPLINE PIECE
Using SST, remove the counter 5th gear together with the counter 5th gear bearing, 2 No. 3 synchromesh shifting keys, No. 3 synchromesh shifting key spring, No. 3 synchronizer ring and No. 5 gear spline piece from the counter 5th gear.
| *a | Hold |
| *b | Turn |
33318
36.REMOVE NO. 5 GEAR SPLINE PIECE
Remove the No. 5 gear spline piece from the counter 5th gear.
33384A
37.REMOVE OUTER NO. 3 SYNCHRONIZER RING
Remove the outer No. 3 synchronizer ring from the counter 5th gear.
33428B
38.REMOVE COUNTER 5TH GEAR BEARING
Remove the counter 5th gear bearing from the counter 5th gear.
33394B
39.REMOVE NO. 3 SYNCHROMESH SHIFTING KEY
Using a snap ring expander, remove the shaft snap ring.
Remove the No. 3 synchromesh shifting keys and No. 3 synchromesh shifting key spring from the counter 5th gear.
| *1 | No. 3 Synchromesh Shifting Key Spring |
| *2 | No. 3 Synchromesh Shifting Key |
| *3 | Counter 5th Gear |
33349
40.REMOVE 5TH GEAR THRUST WASHER
Remove the 5th gear thrust washer from the counter gear.
33349C
41.REMOVE 5TH GEAR THRUST WASHER PIN
Remove the 5th gear thrust washer pin from the counter gear.
33151
42.REMOVE OUTPUT SHAFT REAR BEARING RETAINER
Remove the 4 bolts and output shaft rear bearing retainer from the intermediate plate.
33402
43.REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY
Pull out the reverse idler gear shaft from the rear side and remove the reverse idler gear sub-assembly from the intermediate plate.
33411P
44.REMOVE COUNTER SHAFT CENTER BEARING
Using a snap ring expander, remove the snap ring from the counter shaft center bearing.
Using SST, remove the counter shaft center bearing from the intermediate plate.
Do not drop the counter gear. Hold the front side of the counter gear when removing the bearing outer race.
33421
45.REMOVE COUNTER GEAR
Remove the counter gear from the intermediate plate.
33311
46.REMOVE INPUT SHAFT
Remove the input shaft and No. 2 synchronizer ring from the output shaft.
Do not drop the input shaft bearing or No. 2 synchronizer ring.
33321B
47.REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING (for Center Bearing Side)
Using a snap ring expander, remove the output shaft bearing shaft snap ring from the output shaft center bearing.
33321
48.REMOVE OUTPUT SHAFT
Using a plastic-faced hammer, remove the output shaft by tapping the intermediate plate.