Home › Drivetrain › R150F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION UNIT › 2015.06–2018.06
RM27T0E _52 Drivetrain _053702 R150F MANUAL TRANSMISSION / TRANSAXLE _0260834 MANUAL TRANSMISSION UNIT A

R150F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  REASSEMBLY  


PROCEDURE

Hide 33321 1.INSTALL OUTPUT SHAFT

a.
C272540

Apply gear oil to the sliding part of the output shaft.


b.

Using a plastic-faced hammer, install the output shaft by tapping the intermediate plate.


Hide 33321B 2.INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING (for Center Bearing Side)

a.
C272935

Using a snap ring expander, install the output shaft bearing shaft snap ring to the output shaft center bearing.


Hide 33311 3.INSTALL INPUT SHAFT

a.
C291275

Apply gear oil to the input shaft and No. 2 synchronizer ring, and install them to the output shaft.

NOTICE:
·

Install the No. 2 synchronizer ring so that its groove fits onto the No. 2 synchromesh shifting key.

·

Check that the input shaft rotates smoothly.




Hide 33421 4.INSTALL COUNTER GEAR

a.
C291291

Install the counter gear to the intermediate plate.


Hide 33411P 5.INSTALL COUNTER SHAFT CENTER BEARING

a.
C216003E01
2.829,0.594 3.126,0.738 0.298,0.144 10 SST 2.509,1.33 2.509,0.685 false 2.509,0.685 2.759,0.685 false

Using SST and a hammer, tap in a new counter shaft center bearing to the intermediate plate.

SST
09316-60011  

HINT:

Install the counter shaft center bearing while tapping the tip of the counter gear with a plastic-faced hammer so that the counter gear does not hit the side wall of the output shaft gear by being pushed forward.



b.

Using a snap ring expander, install the snap ring to the counter shaft center bearing.


Hide 33402 6.INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY

a.
D026002

Apply gear oil to the sliding parts of the reverse idler gear sub-assembly and reverse idler gear shaft, and install the reverse idler gear sub-assembly and reverse idler shaft to the intermediate plate.

NOTICE:

Be sure to install the reverse idler gear shaft from the rear with the groove facing the rear side.



Hide 33151 7.INSTALL OUTPUT SHAFT REAR BEARING RETAINER

a.
D026001

Insert the protrusion of the output shaft rear bearing retainer into the groove of the reverse idler gear shaft. Then install the output shaft rear bearing retainer with the 4 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 33349C 8.INSTALL 5TH GEAR THRUST WASHER PIN

a.
C272929

Apply MP grease to the 5th gear thrust washer pin and install it to the counter gear.


Hide 33349 9.INSTALL 5TH GEAR THRUST WASHER

a.
C272927

Apply gear oil to the 5th gear thrust washer and install it to the counter gear.

NOTICE:

Install the 5th gear thrust washer so that its chamfered side faces the front side.



Hide 33394B 10.INSTALL NO. 3 SYNCHROMESH SHIFTING KEY

a.

Apply gear oil to the sliding part of No. 3 transmission hub sleeve and install it to the counter 5th gear.

NOTICE:

Make sure that the No. 3 transmission hub sleeve and counter 5th gear are facing the proper direction.



b.
C248514E05
1.885,2.979 1.792,2.979 1.792,2.979 1.635,2.688 false 1.479,3 1.385,3 1.385,3 1.323,2.729 false 1.51,2.917 1.667,3.073 0.156,0.156 10 true *a 1.927,2.906 2.271,3.115 0.344,0.208 10 true *b

Install the 2 No. 3 synchromesh shifting keys and No. 3 synchromesh shifting key spring to the counter 5th gear as shown in the illustration.

Text in Illustration
*a Cutout
*b Protrusion

HINT:

When installing the No. 3 synchromesh shifting key spring, make sure the protrusion fits into the cutout.



c.
C247403

Using a snap ring expander, install the snap ring to the counter 5th gear.


Hide 33428B 11.INSTALL COUNTER 5TH GEAR BEARING

a.
D026020

Apply gear oil to the counter 5th gear bearing and install it to the counter 5th gear.


Hide 33428 12.INSTALL COUNTER 5TH GEAR

a.
C272976

Apply gear oil to the counter 5th gear and No. 3 transmission hub sleeve, and install the counter 5th gear to the counter gear.


Hide 33384A 13.INSTALL OUTER NO. 3 SYNCHRONIZER RING

a.
C272978

Apply gear oil to the outer No. 3 synchronizer ring and install it to the counter gear.

NOTICE:

Install the outer No. 3 synchronizer ring so that its groove fits onto the No. 3 synchromesh shifting key.



Hide 33318 14.INSTALL NO. 5 GEAR SPLINE PIECE

a.
C216004E01
1.634,1.979 1.937,2.139 0.303,0.160 10 SST 2.141,2.076 1.983,2.076 false 1.68,0.381 1.983,0.541 0.303,0.160 10 SST 1.64,0.469 1.247,0.469 false

Using SST and a press, press in the No. 5 gear spline piece to the counter gear.

SST
09316-60011  (09316-00011)

NOTICE:

Check that the counter 5th gear rotates freely.



Hide 33421R 15.INSTALL COUNTER GEAR REAR SHAFT SNAP RING

a.

Select a counter gear rear shaft snap ring so that the thrust clearance between the No. 5 gear spline piece and counter gear rear shaft snap ring to be within the specification.

Standard clearance:

0.10 mm (0.00394 in.) or less


Snap Ring Thickness:
Thickness
2.85 mm (0.1122 in.)
2.90 mm (0.1141 in.)
2.95 mm (0.1161 in.)
3.00 mm (0.1181 in.)
3.05 mm (0.1200 in.)
3.10 mm (0.1220 in.)
3.15 mm (0.1240 in.)



b.

Secure the intermediate plate in a vise between aluminum plates.


c.
D026023

Using a brass bar and hammer, tap on the counter gear rear shaft snap ring.


Hide 33321A 18.INSTALL OUTPUT SHAFT REAR BEARING

a.
C216005E01
2.556,0.465 2.875,0.626 0.319,0.161 10 SST 2.479,0.566 2.329,0.566 false 2.329,0.566 2.329,0.917 false

Using SST and a hammer, press in the output shaft spacer and a new output shaft rear bearing to the output shaft.

SST
09309-35010  


Hide 33321B 19.INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING (for Rear Bearing Side)

a.

Select a output shaft bearing shaft snap ring so that the thrust clearance between the output shaft bearing shaft and output shaft bearing shaft snap ring to be within the specification.

Standard clearance:

0.10 mm (0.00394 in.) or less


Snap Ring Thickness:
Thickness Thickness
2.65 mm (0.1043 in.) 3.10 mm (0.1220 in.)
2.70 mm (0.1063 in.) 3.15 mm (0.1240 in.)
2.75 mm (0.1083 in.) 3.20 mm (0.1260 in.)
2.80 mm (0.1102 in.) 3.25 mm (0.1280 in.)
2.85 mm (0.1122 in.) 3.30 mm (0.1299 in.)
2.90 mm (0.1142 in.) 3.35 mm (0.1319 in.)
2.95 mm (0.1161 in.) 3.40 mm (0.1339 in.)
3.00 mm (0.1181 in.) 3.45 mm (0.1358 in.)
3.05 mm (0.1200 in.) -



b.
D025988

Using a brass bar and hammer, tap on the output shaft bearing shaft snap ring.


Hide 33228 20.INSTALL REVERSE SHIFT ARM BRACKET

a.
C291035

Install the reverse shift arm to the reverse shift arm bracket with a new snap ring.


b.
C291038E02
0.563,0.827 0.762,0.824 0.762,0.824 1.056,1.024 false 0.385,0.731 0.541,0.913 0.156,0.181 10 *1 1.129,1.637 1.284,1.819 0.156,0.181 10 *2 0.932,1.547 0.969,1.716 0.969,1.716 1.107,1.716 false

Insert the tip of the reverse shift arm into the reverse idler gear sub-assembly.

Text in Illustration
*1 Reverse Idler Gear Sub-assembly
*2 Reverse Shift Arm


c.
C291034

Install the reverse shift arm bracket with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


d.

Install the torsion spring to the reverse shift arm bracket.

NOTICE:

Make sure that the torsion spring is securely installed to the reverse shift arm.



Hide 33211 21.INSTALL REVERSE SHIFT FORK

a.
C290803

Install the reverse shift fork to the reverse shift arm.


Hide 33244D 22.INSTALL NO. 3 GEAR SHIFT FORK SHAFT

a.
C272921

Install the No. 3 shift fork to the No. 3 transmission hub sleeve and the No. 3 gear shift fork shaft to the intermediate plate from the front side.


b.
C289009

Install the straight pin to the reverse shift fork.


c.
C288251

Using a brass bar and hammer, tap on the snap ring to the No. 3 gear shift fork shaft.


d.
C272919

Using a 5 mm pin punch and hammer, tap on the shift fork set slotted spring pin to the No. 3 shift fork.


Hide 33242 23.INSTALL NO. 1 GEAR SHIFT FORK SHAFT

a.
D025975

Install the No. 1 shift interlock roller to the intermediate plate.


b.
C288249

Install the No. 1 shift fork to the reverse gear.


c.
C288248

Install the No. 1 gear shift fork shaft to the intermediate plate from the rear side.


d.
C288247

Install a new bolt to the No. 1 shift fork.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)


e.
C288252

Using a brass bar and hammer, tap in the snap ring to the No. 1 gear shift fork shaft.


Hide 33243A 24.INSTALL NO. 2 GEAR SHIFT FORK SHAFT

a.
D025967

Install the shift interlock pin and No. 1 shift interlock roller to the intermediate plate.


b.
C288245

Install the No. 2 shift fork to the No. 2 transmission hub sleeve.


c.
D029050

Apply gear oil to the No. 2 gear shift fork shaft and install it to the intermediate plate from the rear side.


d.
C288243

Install a new bolt to the No. 2 shift fork.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)


e.
C288253

Using a brass bar and hammer, tap on the snap ring to the No. 2 gear shift fork shaft.


Hide 33275 25.INSTALL NO. 1 SHIFT DETENT BALL SPRING SEAT

a.
C288241

Install the 2 detent balls and 2 compression springs to the intermediate plate.


b.

for Type A:

Apply adhesive to 2 or 3 threads of the 2 No. 1 shift detent ball spring seats.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.
C295053

for Type A:

Using a 6 mm hexagon socket wrench, install the 2 No. 1 shift detent ball spring seats to the intermediate plate.

Torque:
19 N*m (189 kgf*cm, 14 ft.*lbf)


d.
C288240

for Type B:

Using a T40 "TORX" socket wrench, install the 2 No. 1 shift detent ball spring seats to the intermediate plate.

Torque:
19 N*m (189 kgf*cm, 14 ft.*lbf)


e.
D025960

Install the detent ball and low side compression spring to the intermediate plate.


f.

for Type A:

Apply adhesive to 2 or 3 threads of the No. 1 shift detent ball spring seat.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



g.
C295052

for Type A:

Using a 6 mm hexagon socket wrench, install the No. 1 shift detent ball spring seat to the intermediate plate.


h.
D029046

for Type B:

Using a T40 "TORX" socket wrench, install the No. 1 shift detent ball spring seat to the intermediate plate.

Torque:
19 N*m (189 kgf*cm, 14 ft.*lbf)


Hide 33449B 26.INSTALL TRANSMISSION MAGNET

a.
D025957

Clean the transmission magnet and install it to the intermediate plate.


Hide 33111 27.INSTALL MANUAL TRANSMISSION CASE

a.
D029067E17
2.99,0.813 2.698,0.938 false 3.021,0.729 3.177,0.875 0.156,0.146 10 false *a

Apply seal packing to the manual transmission case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Seal diameter:

1.2 mm (0.0472 in.)


Text in Illustration
*a Seal Packing

NOTICE:

Assemble parts within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.



b.
D029117

Place the manual transmission case on wooden blocks.


c.

Using a plastic-faced hammer, tap the intermediate plate to install the manual transmission case.


Hide 33411D 28.INSTALL NO. 1 COUNTER GEAR FRONT BEARING SNAP RING

a.
D025954

Using a snap ring expander, install the No. 1 counter gear front bearing snap ring to the counter gear front bearing.


Hide 33311B 29.INSTALL FRONT BEARING SHAFT SNAP RING

a.
D025953

Using a snap ring expander, install the front bearing shaft snap ring to the input shaft front bearing.


Hide 33131A 30.INSTALL TRANSMISSION FRONT BEARING RETAINER OIL SEAL

a.
C217497E01
2.655,0.127 2.950,0.274 0.295,0.147 10 SST 2.61,0.208 2.426,0.208 false 2.426,0.208 2.289,0.408 false 0.334,0.26 0.629,0.406 0.295,0.147 10 SST 0.994,0.442 0.831,0.319 false 0.831,0.319 0.678,0.319 false 0.995,0.583 0.831,0.319 false 0.291,0.976 0.586,1.122 0.295,0.147 10 SST 0.737,0.732 0.404,0.732 false 0.404,0.732 0.404,0.964 false 0.872,0.846 0.404,0.846 false

Using SST and a hammer, tap in a new transmission front bearing retainer oil seal to the front bearing retainer.

SST
09950-60010  (09951-00300, 09951-00520, 09952-06010)
09950-70010  (09951-07100)

Standard oil seal depth:

11.20 to 12.20 mm (0.441 to 0.480 in.)



b.

Apply a light coat of MP grease to the lip of the transmission front bearing retainer oil seal.


Hide 33131 31.INSTALL FRONT BEARING RETAINER

a.
D026036E06
2.594,0.833 2.302,0.833 false 2.635,0.75 2.792,0.896 0.156,0.146 10 false *a

Apply seal packing to the front bearing retainer as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Seal diameter:

1.2 mm (0.0472 in.)


Text in Illustration
*a Seal Packing

NOTICE:

Assemble parts within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.



b.
D025950

Install the front bearing retainer to the manual transmission case with the 8 bolts.

Torque:
17 N*m (168 kgf*cm, 12 ft.*lbf)


c.

Check that the input shaft and output shaft rotate smoothly.


Hide 36117A 32.INSTALL TRANSFER ADAPTER OIL SEAL

a.
U167477E02
1.167,1.042 1.552,1.531 1.552,1.531 1.24,1.427 true 1.583,1.448 1.906,1.625 0.323,0.177 10 false SST

Using SST and a hammer, tap in a new transfer adapter oil seal to the transfer adapter.

SST
09710-30050  
09950-70010  (09951-07100)

Standard oil seal depth:

45.4 to 46.4 mm (1.79 to 1.82 in.)



b.

Apply a light coat of MP grease to the lip of the transfer adapter oil seal.


Hide 33280 33.INSTALL REVERSE RESTRICT PIN ASSEMBLY

a.
D029042

Install the reverse restrict pin assembly to the transfer adapter.


b.
D033421

Using a 5 mm pin punch and hammer, tap in the reverse restrict pin slotted spring pin to the transfer adapter.


c.
D029040

Using a T40 "TORX" socket wrench, install the reverse restrict pin plug to the transfer adapter.

Torque:
19 N*m (189 kgf*cm, 14 ft.*lbf)


Hide 33124E 34.INSTALL TRANSFER OIL RECEIVER PIPE

a.
D029037

Install the transfer oil receiver pipe to the transfer adapter.


Hide 36117 35.INSTALL TRANSFER ADAPTER

a.
D029067E19
2.99,0.813 2.698,0.938 false 3.021,0.729 3.177,0.875 0.156,0.146 10 false *a

Apply seal packing to the transfer adapter as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Seal diameter:

1.2 mm (0.0472 in.)


Text in Illustration
*a Seal Packing

NOTICE:

Assemble parts within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.



b.
D029119

Using a plastic-faced hammer, tap the transfer adapter to attach it to the manual transmission case.


c.
C357738

Install the transfer adapter to the manual transmission case with the 10 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 33251 36.INSTALL SHIFT AND SELECT LEVER

a.
C216212E01
1.368,0.128 1.518,0.275 0.150,0.147 10 *1 0.177,0.851 0.327,0.999 0.150,0.147 10 *2 2.156,0.225 1.592,0.225 false 0.39,0.934 0.735,0.934 false 0.735,0.934 0.735,1.381 false

Install the shift and select lever with the shift lever housing to the transfer adapter.

Text in Illustration
*1 Shift Lever Housing
*2 Shift and Select Lever


b.
C216209

Install the bolt to the shift lever housing.

Torque:
33 N*m (340 kgf*cm, 25 ft.*lbf)


Hide 33506F 37.INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

a.
C216213

Install the floor shift control shift lever retainer sub-assembly and a new gasket with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 38.INSTALL RESTRICT PIN

a.
C216210

Install the 2 restrict pins.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 84210 39.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

a.
D029030E12
1.927,1.188 2.052,1.875 false 2.354,1.875 2.052,1.875 false 2.417,1.802 2.708,1.948 0.292,0.146 10 false SST

Using SST, install a new gasket and the back-up light switch assembly to the manual transmission case.

SST
09817-16011  

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 31111 40.INSTALL CLUTCH HOUSING

U148543E03
0.948,0.25 1.063,0.417 0.115,0.167 10 false A 2.417,1.958 2.531,2.125 0.115,0.167 10 false A 2.635,1.521 2.75,1.688 0.115,0.167 10 false A 2.708,0.875 2.823,1.042 0.115,0.167 10 false A 2.521,0.417 2.635,0.583 0.115,0.167 10 false A 1.635,0.042 1.75,0.208 0.115,0.167 10 false A 0.813,1.917 0.927,2.083 0.115,0.167 10 false A 0.635,1.354 0.75,1.521 0.115,0.167 10 false B 0.635,0.75 0.75,0.917 0.115,0.167 10 false B

a.

Temporarily install the clutch housing with the 7 bolts labeled A.


b.

Apply adhesive to the 2 bolts labeled B.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.

Temporarily install the 2 bolts labeled B.


d.

Tighten the 9 bolts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 31236B 41.INSTALL RELEASE FORK SUPPORT

Hide 31230 42.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

Hide 31204 43.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

Hide 31126 44.INSTALL CLUTCH RELEASE FORK BOOT

a.

Install the release fork boot to the clutch housing.


Hide 33104 45.INSTALL DRAIN PLUG

a.
D029024

Install a new gasket and the drain plug to the manual transmission case.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 33101A 46.INSTALL MANUAL TRANSMISSION FILLER PLUG

a.
D029023

Install a new gasket and the manual transmission filler plug to the manual transmission case.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)