Home › Drivetrain › VF4BM (TRANSFER / 4WD / AWD) › 4WD CONTROL SWITCH(w/o Combination Switch) › 2015.06–2017.08
RM27T0E _52 Drivetrain _053703 VF4BM TRANSFER / 4WD / AWD _0260843 4WD CONTROL SWITCH(w/o Combination Switch) G

VF4BM TRANSFER / 4WD / AWD  4WD CONTROL SWITCH(w/o Combination Switch)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84223A 1.INSPECT TRANSFER POSITION SWITCH

a.

Check the harness and connector (4 wheel drive control ECU - battery and body ground).

i.
U148710E01
0.097,0.05 0.281,0.213 0.184,0.163 10 *a 2.34,0.268 2.649,0.424 0.309,0.156 10 G54 1.833,1.712 2.174,1.886 0.341,0.174 10 GND 1.81,0.311 2.060,0.476 0.250,0.165 10 IG 2.283,0.897 2.141,0.403 2.141,0.403 2.047,0.403 false 2.146,0.967 2.035,1.689 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G54-3 (IG) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Component with harness connected
(4 wheel drive control ECU)

If the result is not as specified, inspect the harness, fuse or connector. If the harness or connector is malfunctioning, repair or replace the harness or connector. If the harness or connector is normal, replace the 4 wheel drive control ECU (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL ECU>REMOVAL).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-4 (GND) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the harness or connector.



b.

Check the harness and connector (transfer position switch - 4 wheel drive control ECU).

i.

Disconnect the G53 ECU connector.


ii.

Disconnect the G18 switch connector.


iii.

Measure the resistance according to the value(s) in the table below.

U148730E03
1.906,0.813 1.635,1.292 false 2.438,0.802 2.656,1.271 false 5.344,0.667 5.063,1.375 false 5.625,0.688 5.854,1.375 false 2.24,0.813 2.24,1.302 false 4.063,0.031 4.271,0.188 0.208,0.156 10 false *b 0.667,0 0.875,0.167 0.208,0.167 10 false *a 3.458,0.698 3.792,0.896 0.333,0.198 10 false G53 0.948,0.646 1.281,0.844 0.333,0.198 10 false G18 2.604,1.344 2.927,1.5 0.323,0.156 10 false HI*A 2.073,1.344 2.417,1.521 0.344,0.177 10 false GND 1.542,1.344 1.771,1.531 0.229,0.188 10 false LO 4.906,1.396 5.396,1.583 0.49,0.188 10 false 2-4*A 5.771,1.396 6.021,1.594 0.25,0.198 10 false LO

Standard Resistance:
for 1GR-FE, 1KD-FTV, 1GD-FTV:
Tester Connection Condition Specified Condition
G18-2 (LO) - G53-13 (LO) Always Below 1 Ω
G18-2 (LO) - Body ground Always 10 kΩ or higher
G18-4 (GND) - Body ground Always Below 1 Ω

for 2TR-FE, 5L-E:
Tester Connection Condition Specified Condition
G18-2 (LO) - G53-13 (LO) Always Below 1 Ω
G18-2 (LO) - Body ground Always 10 kΩ or higher
G18-4 (GND) - Body ground Always Below 1 Ω
G18-5 (HI) - G53-11 (2-4) Always Below 1 Ω
G18-5 (HI) - Body ground Always 10 kΩ or higher


Text in Illustration
*A for 2TR-FE, 5L-E - -
*a Front view of wire harness connector
(to Transfer Position Switch)
*b Front view of wire harness connector
(to 4 wheel drive control ECU)

If the result is not as specified, repair or replace the harness or connector.



c.

Check the transfer position switch.

i.

Turn the ignition switch off.


ii.

Connect the G18 switch connector.


iii.

Connect the G53 ECU connector.


iv.
U148715E01
0.097,0.05 0.281,0.213 0.184,0.163 10 *a 1.116,0.269 1.424,0.424 0.309,0.156 10 G53 1.833,1.658 2.304,1.832 0.471,0.174 10 2-4*A 0.269,1.658 0.519,1.822 0.250,0.165 10 LO 1.238,1.029 1.934,1.64 false 1.097,1.024 0.415,1.637 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 1GR-FE, 1KD-FTV, 1GD-FTV:
Tester Connection Switch Condition Specified Condition
G53-13 (LO) - Body ground Ignition switch ON
Transfer position switch H4
10.5 to 14 V
Ignition switch ON
Transfer position switch L4
Below 1.5 V

for 2TR-FE, 5L-E:
Tester Connection Switch Condition Specified Condition
G53-11 (2-4) - Body ground Ignition switch ON
Transfer position switch H4F
Below 1.5 V
Ignition switch ON
Transfer position switch H4L
Below 1.5 V
Ignition switch ON
Transfer position switch L4L
10.5 to 14 V
G53-13 (LO) - Body ground Ignition switch ON
Transfer position switch H4F
10.5 to 14 V
Ignition switch ON
Transfer position switch H4L
Below 1.5 V
Ignition switch ON
Transfer position switch L4L
Below 1.5 V


Text in Illustration
*A for 2TR-FE, 5L-E
*a Component with harness connected
(4 wheel drive control ECU)

If the result is not as specified, check the 4 wheel drive control ECU.



d.

Check the 4 wheel drive control ECU.

i.

Disconnect the G18 switch connector.


ii.
U148732E01
0.117,0.063 0.305,0.238 0.189,0.175 10 *a 0.337,0.831 0.674,1.023 0.336,0.193 10 G18 1.16,1.794 1.376,1.942 0.216,0.149 10 LO 2.362,1.794 2.790,1.938 0.428,0.145 10 HI*A 1.601,1.194 1.262,1.756 false 2.203,1.186 2.443,1.759 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 1GR-FE, 1KD-FTV, 1GD-FTV:
Tester Connection Switch Condition Specified Condition
G18-2 (LO) - Body ground Ignition switch ON 10.5 to 14 V

for 2TR-FE, 5L-E:
Tester Connection Switch Condition Specified Condition
G18-2 (LO) - Body ground Ignition switch ON 10.5 to 14 V
G18-5 (HI) - Body ground Ignition switch ON 10.5 to 14 V


Text in Illustration
*A for 2TR-FE, 5L-E
*a Front view of wire harness connector
(to Transfer Position Switch)

If the result is not as specified, replace the 4 wheel drive control ECU (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL ECU>REMOVAL).

If the result is normal, replace the transfer position switch (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH(w/o Combination Switch)>REMOVAL).