37110
1.REMOVE REAR PROPELLER SHAFT ASSEMBLY
Remove the rear propeller shaft assembly (See page Drivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY>REMOVAL).
41204B
2.REMOVE REAR DRIVE PINION NUT
Using SST and a hammer, loosen the staked part of the rear drive pinion nut.
Use SST to hold the companion flange.
Using a 30 mm socket wrench, remove the rear drive pinion nut.
41204
3.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
Using SST, remove the rear drive pinion companion flange sub-assembly.
Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
41201C
4.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL
Using SST, remove the rear differential carrier oil seal.
| *1 | Oil Seal |
| *2 | Oil Slinger |
41214
5.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
Remove the rear differential drive pinion oil slinger.
41201B
6.REMOVE REAR DRIVE PINION FRONT BEARING
Using SST, remove the rear drive pinion tapered roller bearing (inner).
Using SST, tap out the rear drive pinion tapered roller bearing (outer).
41115
7.REMOVE DIFFERENTIAL OIL STORAGE RING
Using a screwdriver and hammer, tap out the differential oil storage ring.
41231
8.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
41231
9.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
Install a new rear differential drive pinion bearing spacer.
Install the spacer so that it is facing in the correct direction.
41115
10.INSTALL DIFFERENTIAL OIL STORAGE RING
Using SST and a hammer, tap in a new differential oil storage ring.
Be careful not to damage the oil storage ring.
41201B
11.INSTALL REAR DRIVE PINION FRONT BEARING
Using SST and a hammer, tap in the rear drive pinion front roller bearing (outer).
Install the rear drive pinion front roller bearing (inner).
41214
12.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
Install the rear differential drive pinion oil slinger.
41201C
13.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL
Apply MP grease to the lip of a new oil seal.
Using SST and a hammer, tap in the rear differential carrier oil seal.
-0.30 to 0.30 mm (-0.0118 to 0.0118 in.)
| *a | Oil Seal Depth |
41204
14.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
Using SST, install the rear drive pinion companion flange sub-assembly.
Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
Using SST to hold the companion flange in place, then slowly tighten a new nut within the drive pinion preload adjustment range so that it reaches the specified drive pinion preload (at Starting).
457 N*m (4660 kgf*cm, 337ft.*lbf) or less
15.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD
Using a torque wrench, measure the preload.
| Item | Specified Condition |
|---|---|
| New bearing | 0.83 to 2.18 N*m (9 to 22 kgf*cm, 8 to 19 in.*lbf) |
| Used bearing | 0.88 to 1.98 N*m (9 to 20 kgf*cm, 8 to 17 in.*lbf) |
If the result is not as specified, adjust the preload.
16.INSPECT TOTAL PRELOAD
Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.
| Item | Specified Condition |
|---|---|
| New bearing | 1.03 to 2.58 N*m (11 to 26 kgf*cm, 10 to 22 in.*lbf) |
| Used bearing | 1.08 to 2.38 N*m (12 to 24 kgf*cm, 10 to 21 in.*lbf) |
41204B
17.STAKE REAR DRIVE PINION NUT
Using a chisel and hammer, stake the rear drive pinion nut.
37110
18.INSTALL REAR PROPELLER SHAFT ASSEMBLY
Install the rear propeller shaft assembly (See page Drivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY>INSTALLATION).
19.INSTALL DIFFERENTIAL OIL
20.CHECK FOR DIFFERENTIAL OIL LEAKAGE