Home › Suspension › SUSPENSION CONTROL › KINETIC DYNAMIC SUSPENSION SYSTEM
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260886 KINETIC DYNAMIC SUSPENSION SYSTEM U

SUSPENSION CONTROL  KINETIC DYNAMIC SUSPENSION SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn ON the intelligent tester.


e.

Enter the following menus: Chassis / KDSS / Data List.


f.

According to the display on the intelligent tester, read the Data List.

KDSS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Oil Pressure Sensor Oil pressure sensor/
Min.: -784.79 MPa (-8002.66 kgf/cm2, -113794.55 psi)
Max.: 784.76 MPa (8002.35 kgf/cm2, 113790.20 psi)
2.6 MPa (26.5 kgf/cm2, 377 psi) to 3.0 MPa (30.6 kgf/cm2, 435 psi): When vehicle stopped and fluid temperature 20°C (68°F) -
Acceleration Sensor Lateral G/
Min.: -1176.37 m/s2
Max.: -1176.33 m/s2
- Changes in proportion with acceleration during turning.
Stop Light Switch Stop light switch/
ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
TC Terminal TC terminal/
ON or OFF
OFF -
TS Terminal TS terminal/
ON or OFF
OFF -
FR Wheel Speed Front wheel RH speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
FL Wheel Speed Front wheel LH speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
RR Wheel Speed Rear wheel RH speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear wheel LH speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
IG Power Source Voltage IG power source voltage/
Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11 to 14 V -
Steering Angle Steering angle/
Min.: -49152.0 deg
Max.: 49150.5 deg
- Changes in proportion with the amount of steering wheel rotation during steering operation.
Compatible Constant Information Compatible constant information/
Min.: 0
Max.: 255
- -
Design Constant Information Design constant information/
Min.: 0
Max.: 255
- -
Accumulator Valve (Downside) Stabilizer control solenoid valve (for Lower Chamber)/
ON or OFF
ON: Stabilizer control solenoid valve closed
OFF: Stabilizer control solenoid valve open
-
Accumulator Valve (Upside) Stabilizer control solenoid valve (for Upper Chamber)/
ON or OFF
ON: Stabilizer control solenoid valve open
OFF: Stabilizer control solenoid valve closed
-
Number of Trouble Codes Number of trouble codes/
Min.: 0
Max.: 255
0 -



ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn ON the intelligent tester.


e.

Enter the following menus: Chassis / KDSS / Active Test.


f.

According to the display on the intelligent tester, perform the Active Test.

KDSS
Tester Display Test Part Control Range Diagnostic Note
Accumulator Valve (Upside) Stabilizer control solenoid valve (for Upper Chamber) Valve ON / OFF The operating sound of the solenoid (clicking sound) can be heard
ON: Data List ON
OFF: Data List OFF
When the Active Test is performed, the solenoid turns on for 3 seconds.
Accumulator Valve (Downside) Stabilizer control solenoid valve (for Lower Chamber) Valve ON / OFF The Operating sound of the solenoid (clicking sound) can be heard
ON: Data List ON
OFF: Data List OFF
When the Active Test is performed, the solenoid turns on for 3 seconds.