Home › Suspension › SUSPENSION CONTROL › KINETIC DYNAMIC SUSPENSION SYSTEM › 2015.06–2021.06
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260886 KINETIC DYNAMIC SUSPENSION SYSTEM C

SUSPENSION CONTROL  KINETIC DYNAMIC SUSPENSION SYSTEM  C1882/82  Power Supply Voltage Malfunction  


DESCRIPTION

The stabilizer control ECU recognizes the ignition switch ON signal based on the voltage input to the IG terminal.

DTC Code DTC Detection Condition Trouble Area
C1882/82 The IG terminal voltage is 10 V or less or 16 V or higher for 0.5 seconds
·

Battery

·

Charging system

·

KDSS fuse

·

Harness or connector

·

Stabilizer control ECU



WIRING DIAGRAM

C194309E43
1.083,1.073 2.083,1.26 1,0.188 10 false from IG Circuit 3.125,1.229 3.583,1.417 0.458,0.188 10 false KDSS 5.115,2.677 6.469,2.906 1.354,0.229 10 false G123 5.115,2.844 6.563,3.073 1.448,0.229 10 false Stabilizer Control ECU 5.229,1.104 5.448,1.271 0.219,0.167 10 false IG 4.917,0.979 5.146,1.135 0.229,0.156 10 false 24 5.229,1.458 5.563,1.625 0.333,0.167 10 false GND 4.906,1.344 5.115,1.51 0.208,0.167 10 false 22

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (IG POWER SOURCE VOLTAGE)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / KDSS / Data List.


f.

Select the item below in the Data List, and read the value displayed on the intelligent tester.

KDSS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG Power Source Voltage IG Power Source Voltage/
Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11 to 14 V -

Standard voltage:

11 to 14 V




OK

2.RECONFIRM DTC

NG

3.CHECK HARNESS AND CONNECTOR (IG TERMINAL)
2.RECONFIRM DTC

b.

Check for DTCs (See page Suspension>SUSPENSION CONTROL>KINETIC DYNAMIC SUSPENSION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

REPLACE STABILIZER CONTROL ECU

B

3.CHECK HARNESS AND CONNECTOR (IG TERMINAL)
a.

Disconnect the Stabilizer control ECU connector.


b.
U148485E02
1.865,1.24 1.563,1.771 1.563,1.771 1.427,1.771 false 0.208,0.073 0.406,0.271 0.198,0.198 10 false *a 1.583,0.26 1.99,0.406 0.406,0.146 10 false G123 1.229,1.688 1.469,1.865 0.24,0.177 10 false IG

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G123-24 (IG) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stabilizer Control ECU)



OK

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Disconnect the Stabilizer control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G123-22 (GND) - Body ground Always Below 1 Ω




OK

REPLACE STABILIZER CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR