Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2015.06–2017.08
RM27T0E _53 Suspension _053710 TIRE PRESSURE MONITORING _0260907 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This is the power source for the tire pressure warning ECU and receiver.

WIRING DIAGRAM

C147971E50
4.219,2.292 4.583,2.479 0.365,0.188 10 false R41 4.198,2.448 6.917,2.656 2.719,0.208 10 false Tire Pressure Warning ECU and Receiver 5.083,0.656 5.302,0.917 0.219,0.26 10 false IG 5.083,1.719 5.458,1.927 0.375,0.208 10 false GND 4.813,0.49 4.969,0.74 0.156,0.25 10 false 1 4.708,1.594 4.906,1.781 0.198,0.188 10 false 12 3.198,0.792 4.156,0.948 0.958,0.156 10 false ECU-IG NO. 1 0.958,0.635 2.052,0.823 1.094,0.188 10 false from IG Circuit

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECU - BATTERY)
a.
U170639E02
0.74,1.5 1.25,1.385 true 0.125,0.021 0.604,0.219 0.479,0.198 10 false *a 1.552,0.458 1.906,0.656 0.354,0.198 10 false R41 0.51,1.438 0.99,1.635 0.479,0.198 10 false IG

Disconnect the tire pressure warning ECU and receiver R41 connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R41-1 (IG) - Body ground Ignition switch ON 10 to 16 V
Ignition switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)



OK

2.CHECK HARNESS AND CONNECTOR (ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ECU - BODY GROUND)
a.
U149317E03
2.073,1.563 2.646,1.833 true 0.125,0.021 0.604,0.219 0.479,0.198 10 false *a 1.563,0.458 1.938,0.656 0.375,0.198 10 false R41 2.688,1.76 3.167,1.958 0.479,0.198 10 false GND

Disconnect the tire pressure warning ECU and receiver R41 connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R41-12 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)



OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR