Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2015.06–2017.08
RM27T0E _53 Suspension _053710 TIRE PRESSURE MONITORING _0260907 TIRE PRESSURE WARNING SYSTEM D

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  INITIALIZATION  


NOTICE:
·

Initialization can be confirmed through the tire pressure warning light.

·

The order in which the data is received is random.

·

If the signals from all the wheels are received, initialization is completed.

·

Initialization is completed when the Data List "ID Tire Inflation Pressure" display shows the correct pressures (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DATA LIST / ACTIVE TEST).

·

Initialization is normally completed within a few minutes.

·

It may take up to a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2124/24 (C2121/21 to C2125/25: w/ Spare Tire) (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>C2121/21).

·

If initialization has not been completed successfully, DTC C2177/77 is stored after a vehicle speed of 37 km/h (23 mph) or more continues for 20 minutes or more.

·

During test mode (sensor check mode), the system will not change to initialization mode even if the tire pressure warning reset switch is pushed.

·

w/ ID Switching Function:

While the answer-back function for the ID switching function is operating, the system will not change to initialization mode even if the tire pressure warning reset switch is pressed.

·
C217594E11
0.154,0.084 0.828,0.37 0.675,0.286 10 *a 1.964,1.792 2.481,1.971 0.517,0.179 10 TC 1.202,1.792 1.553,1.971 0.351,0.179 10 CG 1.805,1.424 2.049,1.764 false 1.571,1.024 1.366,1.761 false

Initialization can be terminated by connecting terminals 13 (TC) and 4 (CG) of the DLC3.



Text in Illustration
*a Front view of DLC3

BEFORE INITIALIZATION


a.

Make sure that the tires are cold.


b.

Set the air pressure of all tires to the specified value(s) (See page Suspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION).



INITIALIZATION PROCEDURE


a.

Turn the ignition switch ON.


b.

Press and hold the tire pressure warning reset switch for 3 seconds or more so that the tire pressure warning light blinks 3 times.

C291559E01
0.193,0.24 0.399,0.410 0.207,0.170 10 *1 2.983,2.08 3.190,2.250 0.207,0.170 10 *2 0.364,1.775 0.571,1.945 0.207,0.170 10 *a 1.274,0.027 1.480,0.197 0.207,0.170 10 *A 4.194,0.071 4.400,0.241 0.207,0.170 10 *B 1.396,1.672 1.602,1.841 0.207,0.170 10 *b 1.217,2.59 1.424,2.760 0.207,0.170 10 *b 0.539,1.993 0.745,2.162 0.207,0.170 10 *c 0.539,2.217 0.745,2.386 0.207,0.170 10 *d 3.154,0.283 3.360,0.453 0.207,0.170 10 *1 6.422,2.078 6.629,2.248 0.207,0.170 10 *2 3.99,1.714 4.197,1.884 0.207,0.170 10 *a 4.975,1.658 5.181,1.827 0.207,0.170 10 *b 4.796,2.596 5.002,2.766 0.207,0.170 10 *b 4.117,1.982 4.324,2.152 0.207,0.170 10 *c 4.117,2.207 4.324,2.376 0.207,0.170 10 *d

Text in Illustration
*A for RHD *B for LHD
*1 Tire Pressure Warning Light *2 Tire Pressure Warning Reset Switch
*a Tire Pressure Warning Light Output Pattern *b 1 sec.
*c ON *d OFF


c.

Turn the ignition switch off.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch ON and turn the GTS on.


f.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


g.

Check that initialization has been completed.


h.

Confirm that the tire pressure data of all tires is displayed on the GTS screen.