Home › Suspension › TIRE / WHEEL › TIRE AND WHEEL SYSTEM › 2015.06–2017.08
RM27T0E _53 Suspension _053711 TIRE / WHEEL _0260908 TIRE AND WHEEL SYSTEM G

TIRE / WHEEL  TIRE AND WHEEL SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT TIRES

a.

Check the tires for wear and proper inflation pressure.

Cold Tire Inflation Pressure (for Europe):
Tire Size Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
P245/70R17 108S 220 (2.2, 32) 220 (2.2, 32)
245/70R17 110S 220 (2.2, 32) 220 (2.2, 32)
P265/65R17 110S 220 (2.2, 32) 220 (2.2, 32)
265/65R17 112S 220 (2.2, 32) 220 (2.2, 32)
P265/60R18 109H 220 (2.2, 32) 220 (2.2, 32)
265/60R18 110H 220 (2.2, 32) 220 (2.2, 32)


Cold Tire Inflation Pressure (for Eastern Europe and Russia):
Tire Size Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
245/70R17 110S 200 (2.0, 29) 200 (2.0, 29)
265/65R17 112S 200 (2.0, 29) 200 (2.0, 29)
265/60R18 110H 200 (2.0, 29) 200 (2.0, 29)


Cold Tire Inflation Pressure (for General Export, Australia, G.C.C.):
Tire Size Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
245/70R17 110S 200 (2.0, 29) 200 (2.0, 29)
265/65R17 112S 200 (2.0, 29) 200 (2.0, 29)
265/60R18 110H 200 (2.0, 29) 200 (2.0, 29)



b.
C137874

Using a dial indicator, check the tire runout.

Standard tire runout:

2.0 mm (0.0787 in.) or less



Hide 2.ROTATE TIRES

a.
C200706C01
1.677,0.427 1.99,0.625 0.313,0.198 10 false *b 1.729,2.542 2.042,2.74 0.313,0.198 10 false *c 0.302,1.573 0.615,1.771 0.313,0.198 10 false *a 0.333,3.583 0.646,3.781 0.313,0.198 10 false *a

Rotate the tires as shown in the illustration.

Torque:
for steel wheel : 112 N*m (1137 kgf*cm, 82 ft.*lbf)
for aluminum wheel : 103 N*m (1050 kgf*cm, 76 ft.*lbf)

Text in Illustration
*a Front of the Vehicle
*b for Vehicles with Spare Tire
*c for Vehicles without Spare Tire


Hide 3.INSPECT WHEEL BALANCE

a.
C144019

for Steel Wheel Type:

Check and adjust the off-the-car balance.

Standard Imbalance After Adjustment:

12 g (0.0265 lb.) or less


HINT:

If necessary, check and adjust the on-the-car balance.



b.

for Aluminum Wheel Type:

Check and adjust the off-the-car balance.

Standard Imbalance After Adjustment:

6.0 g (0.0132 lb.) or less


C241067E02
0.675,0.215 0.891,0.398 0.216,0.184 10 *a 4.364,0.215 4.580,0.398 0.216,0.184 10 *b 1.013,2.922 1.155,3.106 0.142,0.184 10 A 4.607,2.943 4.749,3.127 0.142,0.184 10 A 5.868,2.964 6.010,3.148 0.142,0.184 10 A

Text in Illustration
*a for 17 Inch Wheels *b for 18 Inch Wheels

NOTICE:
·

Using a cleaning detergent, remove dirt, oil and water from the surface where the balance weight is to be adhered.

·

Do not touch the adhesive surface of the tape.

·

Attach a sticking type balance weight to the flat surface (A) shown in the illustration.

Width (A):

25 mm (0.984 in.)


·

Push the balance weight securely with your finger so that it securely adheres to the position.

·

Do not reuse the balance weight.



HINT:
·

For 17 inch wheels, the outer side balance weight should be installed by clipping it to the rim.

·

If necessary, check and adjust the on-the-car balance.




Hide 4.INSPECT FRONT AXLE HUB BEARING LOOSENESS

Hide 6.INSPECT REAR AXLE SHAFT RUNOUT