Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260910 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to output the DTCs by blinking the ABS warning light and slip indicator light.

WIRING DIAGRAM

C200425E46
1.242,4.324 3.735,4.517 2.493,0.193 10 : CAN Communication System 4.296,1.371 4.573,1.545 0.276,0.174 10 A6 4.296,1.563 7.112,1.752 2.816,0.188 10 Brake Actuator Assembly (Skid Control ECU) 6.062,3.735 6.523,3.928 0.461,0.193 10 DLC3 6.062,3.557 6.421,3.741 0.360,0.184 10 G48 5.986,2.625 6.245,2.807 0.259,0.182 10 TC 5.978,2.988 6.291,3.190 0.313,0.202 10 CG 5.763,2.894 5.948,3.048 0.185,0.154 10 4 5.683,2.489 5.922,2.672 0.239,0.184 10 13 1.42,1.344 2.527,1.528 1.107,0.184 10 19*1, 17*2 1.025,1.491 1.284,1.673 0.259,0.182 10 TC 0.635,2.016 2.270,2.209 1.635,0.193 10 G180*1, G183*2 0.635,2.194 1.059,2.387 0.424,0.193 10 ECM 0.614,3.564 1.444,3.762 0.830,0.198 10 *2: for 5L-E 0.614,3.235 2.444,3.433 1.830,0.198 10 *1: for 2TR-FE

HINT:

When the warning lights continue to blink, a ground short in the wiring of terminal 13 (TC) of the DLC3 or an internal ground short in one or more ECUs is suspected.


CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).


PROCEDURE

2.INSPECT DLC3
a.
U115769E01
0.108,0.087 0.413,0.237 0.304,0.151 10 *a 2.137,0.207 2.441,0.358 0.304,0.151 10 CG 2.205,1.943 2.510,2.094 0.304,0.151 10 TC 1.84,1.465 2.039,2.009 2.039,2.009 2.172,2.009 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G48-13 (TC) - G48-4 (CG) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of DLC3



OK

3.INSPECT ECM (DLC3 INPUT)

NG

4.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
3.INSPECT ECM (DLC3 INPUT)
SST
09843-18040  

a.

Turn the ignition switch off.


b.
U115769E01
0.108,0.087 0.413,0.237 0.304,0.151 10 *a 2.137,0.207 2.441,0.358 0.304,0.151 10 CG 2.205,1.943 2.510,2.094 0.304,0.151 10 TC 1.84,1.465 2.039,2.009 2.039,2.009 2.172,2.009 false

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

Text in Illustration
*a Front view of DLC3


c.

Turn the ignition switch to ON.


d.

Check that the MIL is blinking.

Result
Result Proceed to
MIL is blinking A
MIL is not blinking B

HINT:

Refer to the ECM installation procedure (for 5L-E: See page Engine / Hybrid System>5L-E (ENGINE CONTROL)>ECM>REMOVAL, for 2TR-FE: See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>ECM>REMOVAL)




A

B

REPAIR OR REPLACE WIRE HARNESS OR ECM

4.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
a.

Turn the ignition switch off.


b.

for 5L-E:

i.

Disconnect the G183 ECM connector.



c.

for 2TR-FE:

i.

Disconnect the G180 ECM connector.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 5L-E:
Tester Connection Condition Specified Condition
G48-13 (TC) - G183-17 (TC) Always Below 1 Ω
G48-13 (TC) - Body ground Always 10 kΩ or higher

for 2TR-FE:
Tester Connection Condition Specified Condition
G48-13 (TC) - G180-19 (TC) Always Below 1 Ω
G48-13 (TC) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G48-4 (CG) - Body ground Always Below 1 Ω




OK

6.INSPECT ECM (DLC3 INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ECM (DLC3 INPUT)
SST
09843-18040  

a.

Turn the ignition switch off.


b.

Connect the ECM connector.


c.
U115769E01
0.108,0.087 0.413,0.237 0.304,0.151 10 *a 2.137,0.207 2.441,0.358 0.304,0.151 10 CG 2.205,1.943 2.510,2.094 0.304,0.151 10 TC 1.84,1.465 2.039,2.009 2.039,2.009 2.172,2.009 false

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

Text in Illustration
*a Front view of DLC3


d.

Turn the ignition switch to ON.


e.

Check that the MIL is blinking.

Result
Result Proceed to
MIL is blinking A
MIL is not blinking B



A

B

REPAIR OR REPLACE WIRE HARNESS OR ECM