Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR › 2015.06–2020.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260921 BRAKE ACTUATOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 2.REMOVE AIR CLEANER CASE SUB-ASSEMBLY (for 2TR-FE)

Hide 3.REMOVE AIR CLEANER CASE ASSEMBLY (for 5L-E)

Hide 4.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C213640

Release the lock lever and disconnect the brake actuator connector.

NOTICE:

Be careful not to allow brake fluid to enter the removed connector.



b.

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator.


c.
C213641E02
1.844,1.583 2.344,1.458 2.344,1.458 2.854,1.458 true 1.5,1.74 1.385,1.813 1.385,1.813 1.385,1.927 true 1.698,0.885 1.698,0.406 1.698,0.406 2.198,0.406 true 1.469,0.938 1.469,0.115 1.469,0.115 1.365,0.115 true 1.24,1 1.24,0.271 1.24,0.271 1.042,0.271 true 1.021,1.052 0.594,0.271 0.594,0.271 0.354,0.271 true 2.208,0.344 2.365,0.5 0.156,0.156 10 true *1 0.156,0.198 0.313,0.354 0.156,0.156 10 false *2 0.833,0.198 0.99,0.354 0.156,0.156 10 false *3 1.177,0.031 1.333,0.188 0.156,0.156 10 false *4 2.875,1.375 3.031,1.531 0.156,0.156 10 true *5 1.323,1.958 1.479,2.115 0.156,0.156 10 false *6

Place tags or marks to identify the installation locations of each brake line.

HINT:
·

*1: To front wheel cylinder RH

·

*2: To front wheel cylinder LH

·

*3: To rear wheel cylinder RH

·

*4: To rear wheel cylinder LH

·

*5: From front master cylinder

·

*6: From rear master cylinder




d.
C213642

Remove the 3 nuts and brake actuator with bracket from the body.

NOTICE:
·

Do not damage the brake lines or wire harness.

·

Do not hold the actuator by the connector.

·

If the actuator is dropped, replace it.




Hide 5.REMOVE BRAKE ACTUATOR BRACKET

a.
C213643

Remove the 3 bolts and brake actuator bracket from the brake actuator.

NOTICE:
·

Do not damage the brake lines or wire harness.

·

Do not hold the actuator by the connector.

·

If the actuator is dropped, replace it.




Hide 6.REMOVE BRAKE ACTUATOR CASE COLLAR

a.
U148365

Remove the 3 brake actuator case collars from the brake actuator bolt cushions.


Hide 7.REMOVE BRAKE ACTUATOR BOLT CUSHION

a.

Remove the 3 brake actuator bolt cushions from the brake actuator bracket.