Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

WIRING DIAGRAM

C200425E45
1.242,4.317 3.194,4.509 1.951,0.193 10 : CAN Communication System 4.296,1.371 5.230,1.545 0.934,0.174 10 A7 4.296,1.563 7.112,1.752 2.816,0.188 10 Master Cylinder Solenoid (Skid Control ECU) 6.062,3.735 6.523,3.928 0.461,0.193 10 DLC3 6.062,3.557 6.426,3.741 0.364,0.184 10 G48 5.986,2.625 6.245,2.807 0.259,0.182 10 TC 5.978,2.988 6.291,3.190 0.313,0.202 10 CG 5.763,2.894 5.948,3.048 0.185,0.154 10 4 5.683,2.489 5.922,2.672 0.239,0.184 10 13 1.42,1.344 3.284,1.528 1.864,0.184 10 6*1, 28*2, 23*3, 25*4 1.025,1.491 1.284,1.673 0.259,0.182 10 TC 0.635,2.016 2.680,2.209 2.045,0.193 10 G55*1, G56*2, G58*3, G184*4 0.635,2.194 1.059,2.387 0.424,0.193 10 ECM 0.572,3.957 1.915,4.140 1.343,0.184 10 *4: for 1GD-FTV 0.572,3.592 2.332,3.818 1.760,0.225 10 *3: for 1KD-FTV 0.572,3.232 3.280,3.415 2.708,0.184 10 *2: for 1GR-FE (Manual Transmission) 0.572,2.878 3.374,3.062 2.802,0.184 10 *1: for 1GR-FE (Automatic Transmission)

HINT:

When each warning light continues blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.


CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).


PROCEDURE

1.INSPECT DLC3
a.

Turn the ignition switch to ON.


b.
U115769E01
0.108,0.087 0.413,0.237 0.304,0.151 10 *a 2.137,0.207 2.441,0.358 0.304,0.151 10 CG 2.205,1.943 2.510,2.094 0.304,0.151 10 TC 1.84,1.465 2.039,2.009 2.039,2.009 2.172,2.009 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G48-13 (TC) - G48-4 (CG) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of DLC3



OK

2.CHECK CAN COMMUNICATION LINE

NG

4.CHECK HARNESS AND CONNECTOR (ECM - DLC3)
3.CHECK DTC (CAN COMMUNICATION SYSTEM)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Check for DTCs (for LHD: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM, for RHD: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN system DTC is not output A
CAN system DTC is output (for LHD) B
CAN system DTC is output (for RHD) C



A

4.CHECK HARNESS AND CONNECTOR (ECM - DLC3)

B

C

4.CHECK HARNESS AND CONNECTOR (ECM - DLC3)
a.

Turn the ignition switch off.


b.

for 1GR-FE (Automatic Transmission):

Disconnect the G55 ECM connector.

for 1GR-FE (Manual Transmission):

Disconnect the G56 ECM connector.

for 1KD-FTV:

Disconnect the G58 ECM connector.

for 1GD-FTV:

Disconnect the G184 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE (Automatic Transmission)
Tester Connection Condition Specified Condition
G55-6 (TC) - G48-13 (TC) Always Below 1 Ω

for 1GR-FE (Manual Transmission)
Tester Connection Condition Specified Condition
G56-28 (TC) - G48-13 (TC) Always Below 1 Ω

for 1KD-FTV
Tester Connection Condition Specified Condition
G58-23 (TC) - G48-13 (TC) Always Below 1 Ω

for 1GD-FTV
Tester Connection Condition Specified Condition
G184-25 (TC) - G48-13 (TC) Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G48-4 (CG) - Body ground Always Below 1 Ω




OK

6.CHECK ECM (DLC3 INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ECM (DLC3 INPUT)
a.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040  

b.
U115769E01
0.108,0.087 0.413,0.237 0.304,0.151 10 *a 2.137,0.207 2.441,0.358 0.304,0.151 10 CG 2.205,1.943 2.510,2.094 0.304,0.151 10 TC 1.84,1.465 2.039,2.009 2.039,2.009 2.172,2.009 false

Check that the MIL is blinking.

Result
Result Proceed to
MIL is blinking A
MIL is not blinking B

Text in Illustration
*a Front view of DLC3


HINT:

Refer to the ECM installation procedures:

for 1GR-FE (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL)

for 1KD-FTV (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECM>REMOVAL)

for 1GD-FTV (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL)



A

7.CHECK DTC (CAN COMMUNICATION SYSTEM)

B

REPAIR OR REPLACE WIRE HARNESS OR ECM

7.CHECK DTC (CAN COMMUNICATION SYSTEM)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Check for DTCs (for LHD: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM, for RHD: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN system DTC is not output (for LHD) A
CAN system DTC is not output (for RHD) B
CAN system DTC is output (for LHD) C
CAN system DTC is output (for RHD) D



A

B

C

D