Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  DTC CHECK / CLEAR  


DTC CHECK/CLEAR (When Using Intelligent Tester)


a.

Check for DTCs.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Chassis / ABS/VSC/TRC / DTC.


v.

Read the DTCs by following the prompts on the intelligent tester screen.



b.

Clear the DTCs.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Chassis / ABS/VSC/TRC / DTC.


v.

Operate the intelligent tester to clear the codes.

HINT:

Refer to the intelligent tester operator's manual for further details.





DTC CHECK/CLEAR (When Using SST Check Wire)


a.

Check for DTCs.

i.
U115769E01
0.108,0.087 0.413,0.237 0.304,0.151 10 *a 2.137,0.207 2.441,0.358 0.304,0.151 10 CG 2.205,1.943 2.510,2.094 0.304,0.151 10 TC 1.84,1.465 2.039,2.009 2.039,2.009 2.172,2.009 false

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

Text in Illustration
*a Front view of DLC3


ii.

Turn the ignition switch to ON.


iii.

Read the DTCs output from the ABS warning light and slip indicator light in the combination meter.

HINT:
·

When the system is normal, the ABS warning light and slip indicator light blink at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).

·

When only 1 DTC is stored, the light outputs the same code after an interval of 4 seconds. Example: When DTC 21 is stored, the light blinks twice, turns off for 1.5 seconds, blinks once, turns off for 4 seconds, and then repeats this output pattern.

·

When 2 or more DTCs are stored, the light outputs the codes with an interval of 2.5 seconds between each different code, and the output of all codes repeats after an interval of 4 seconds.

·

If no code is output, inspect the TC and CG terminal circuit and the ABS warning light and slip indicator light circuits.


Trouble Area See Procedure
TC and CG terminal circuit (Click here)
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)
Slip indicator light circuit (Remains on) (Click here)
Slip indicator light circuit (Does not come on) (Click here)



iv.

The codes are explained in the code table.

ABS DTC
ABS Warning Light Display Intelligent Tester Display
11 C0278
12 C0279
21 C0226
22 C0236
23 C0246
24 C0256
25 C1225
26 C1226
27 C1227
28 C1228
31 C1401
C1405
C1409
32 C1402
C1406
C1410
33 C1403
C1407
C1411
34 C1404
C1408
C1412
35 C1413
36 C1414
37 C1337
38 C1415
39 C1416
41 C1241
C1417
42 C1242
43 C1243
44 C1419
C1420
C1442
45 C1245
46 C1421
C1422
C1423
C1424
C1455
C1456
C1457
C1458
49 C1425
51 C1251
52 C1252
53 C1253
54 C1254
56 C1256
C1452
57 C1257
58 C1453
C1454
68 C1268
94 U0073
95 U0124
97 C1381
A1* U0114

*: The light blinks 10 times, turns off for 1.5 seconds, and then blinks once.


VSC DTC
Slip Indicator Light Display Intelligent Tester Display
13 C120A
31 C1432
C1433
C1434
32 C1232
34 C1435
C1436
C1443
36 C1210
39 C1336
43* -
47 C1340
51 C1201
53 C1203
62 U0123
63 U0126
64 C1380
65 C1437
U0100
66 C1290
C1439
C1445
98 C1440

*: This DTC is output when the VSC system detects a malfunction in the ABS.



v.

Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

If 2 or more DTCs are output at the same time, the DTCs are output in ascending order.



b.

Clear the DTCs.

i.
U115769E01
0.108,0.087 0.413,0.237 0.304,0.151 10 *a 2.137,0.207 2.441,0.358 0.304,0.151 10 CG 2.205,1.943 2.510,2.094 0.304,0.151 10 TC 1.84,1.465 2.039,2.009 2.039,2.009 2.172,2.009 false

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

Text in Illustration
*a Front view of DLC3


ii.

Turn the ignition switch to ON.


iii.

Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.


iv.

Check that the ABS warning light and slip indicator light blink at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).


v.

Remove SST from the terminals of the DLC3.




END OF DTC CHECK/CLEAR


a.

Turn the ignition switch to ON.


b.

Check that the ABS warning light and slip indicator light go off within approximately 3 seconds.