Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  C0226  SFR Solenoid Circuit  C0236  SFL Solenoid Circuit  C0246  SRR Solenoid Circuit  C0256  SRL Solenoid Circuit  C1225  SM Solenoid Circuit  


DESCRIPTION

These solenoids turn on when signals are received from the skid control ECU and control the pressure acting on the wheel cylinders to control the braking force.

DTC Code DTC Detection Condition Trouble Area
C0226
C0236
C0246
C0256
An open or short in the solenoid circuit continues for 0.05 seconds or more.
·

Solenoid circuit

·

Brake actuator assembly


C1225 One of the following conditions is met:
1.

While switching solenoid (SM1 or SM2) is outputting ON, overcurrent continues for 0.1 seconds or more.

2.

While switching solenoid (SM1 or SM2) is outputting OFF, an open circuit continues for 0.05 seconds or more.

3.

While switching solenoid (SM1 or SM2) is outputting ON, an open circuit continues for 0.05 seconds or more.

4.

While switching solenoid (SM1 or SM2) is outputting OFF, current continues to be applied for 0.05 seconds or more.

5.

A condition in which the outputs from switching solenoids 1 and 2 are different continues for 0.2 seconds or more.


·

SM1 or SM2 circuit

·

Brake actuator assembly



WIRING DIAGRAM

C215405E13
1.531,1.385 2.313,1.531 0.781,0.146 10 false ABS NO. 2 3.26,1.115 3.438,1.271 0.177,0.156 10 false 12 3.313,5 3.417,5.156 0.104,0.156 10 false 1 3.542,1.354 3.938,1.51 0.396,0.156 10 false +BS 3.542,5.083 3.958,5.24 0.417,0.156 10 false GND1 4.521,1.177 5.5,1.354 0.979,0.177 10 false Solenoid Relay 4.406,4.458 5.531,4.615 1.125,0.156 10 false Skid Control ECU 5.938,1.969 6.344,2.125 0.406,0.156 10 false SFRH 5.938,2.49 6.323,2.646 0.385,0.156 10 false SFLH 5.927,2.99 6.344,3.146 0.417,0.156 10 false SRRH 5.938,3.5 6.333,3.656 0.396,0.156 10 false SRLH 5.938,3.99 6.344,4.146 0.406,0.156 10 false SFRR 5.927,4.5 6.333,4.656 0.406,0.156 10 false SFLR 5.927,5 6.344,5.156 0.417,0.156 10 false SRRR 5.938,5.5 6.354,5.656 0.417,0.156 10 false SRLR 5.979,6.01 6.323,6.167 0.344,0.156 10 false SM1 5.979,6.5 6.313,6.656 0.333,0.156 10 false SM2 3.5,8.26 3.958,8.417 0.458,0.156 10 false A6 3.5,8.427 5.354,8.583 1.854,0.156 10 false Brake Actuator Assembly 0.323,2.521 1.677,2.75 1.354,0.229 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CALIBRATION).


PROCEDURE

1.RECONFIRM DTC
HINT:

These codes are stored when a problem is detected in the brake actuator assembly.

The solenoid circuits are in the brake actuator assembly.

Therefore, solenoid circuit inspections and solenoid unit inspections cannot be performed. Be sure to check if any DTCs are output before replacing the brake actuator assembly.



b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC not output A
DTC output B

HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU with the ignition switch ON and the stop light switch off, the ECU performs self-diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harnesses, and fuses of the brake actuator assembly. Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the brake actuator assembly (skid control ECU), inspect and repair the connector or wire harness. The DTCs were probably output due to a bad connection of the connector terminal.





A

B