Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  C1241  Low Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (housed in the actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit, such as the battery or generator circuit, etc.

The DTC is cleared when the IG1 terminal voltage returns to normal.

DTC Code DTC Detection Condition Trouble Area
C1241 One of the following conditions is met:
1.

At a vehicle speed of 3 km/h (2 mph) or more, the IG1 terminal voltage is below 9.5 V for 10 seconds or more.

2.

When the solenoid relay remains on and the IG1 terminal voltage is below 9.5 V, the relay contact is open for 0.22 seconds or more.

3.

With the IG1 terminal voltage at 9.5 V or less, the vehicle speed sensor power supply decreases for 60 seconds or more.


·

ECU-IG NO. 1 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of the skid control ECU



WIRING DIAGRAM

C194309E45
0.979,1.094 2.01,1.281 1.031,0.188 10 false from IG1 Circuit 2.896,1.26 3.813,1.448 0.917,0.188 10 false ECU-IG NO. 1 5.229,1.073 5.688,1.271 0.458,0.198 10 false IG1 4.927,0.927 5.208,1.115 0.281,0.188 10 false 34 5.25,1.5 5.708,1.698 0.458,0.198 10 false GND1 5.01,1.302 5.219,1.49 0.208,0.188 10 false 1 5.115,2.656 5.313,2.833 0.198,0.177 10 false A6 5.104,2.844 6.75,3.219 1.646,0.375 10 false Brake Actuator Assembly (Skid Control ECU)

CAUTION / NOTICE / HINT

NOTICE:
·
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (IG1)
a.

Disconnect the A6 skid control ECU connector.


b.
U148254E04
2.167,1.948 2.25,1.948 2.25,1.948 2.313,1.396 false 0.281,0.042 0.573,0.24 0.292,0.198 10 false *a 1.875,1.865 2.156,2.031 0.281,0.167 10 false IG1 0.26,1.01 0.51,1.198 0.25,0.188 10 false A6

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A6-34 (IG1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the skid control ECU connector.



c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC not output A
DTC output B



A

B