Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  C1405  Open or Short in Front Speed Sensor RH Circuit  C1406  Open or Short in Front Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1401 and C1402 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>C1401).

DTC Code DTC Detection Condition Trouble Area
C1405
C1406
Either condition is met:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Front speed sensor RH/LH

·

Skid control sensor wire

·

Speed sensor circuit

·

Brake actuator assembly (Skid control ECU)



HINT:
·

DTC C1405 is for the front speed sensor RH.

·

DTC C1406 is for the front speed sensor LH.



WIRING DIAGRAM

C217214E69
5.573,2.708 5.813,2.854 0.24,0.146 10 false A6 5.552,2.885 7.156,3.26 1.604,0.375 10 false Brake Actuator Assembly (Skid Control ECU) 3.052,1.198 5.74,1.375 2.688,0.177 10 false Front Skid Control Sensor Wire RH 3.927,0.333 4.208,0.563 0.281,0.229 10 false Ap1 3.917,1.865 4.208,2.094 0.292,0.229 10 false Ap2 2.823,0.313 3.031,0.531 0.208,0.219 10 false p1 2.813,1.865 3.021,2.073 0.208,0.208 10 false p2 0.458,0.615 2,0.823 1.542,0.208 10 false Front Speed Sensor RH 0.469,2.115 2.01,2.323 1.542,0.208 10 false Front Speed Sensor LH 2.417,0.333 2.708,0.51 0.292,0.177 10 false FR- 2.844,0.646 3.01,0.844 0.167,0.198 10 false 2 2.406,0.792 2.698,0.969 0.292,0.177 10 false FR+ 4,0.646 4.135,0.813 0.135,0.167 10 false 2 4,0.115 4.177,0.271 0.177,0.156 10 false 1 2.854,0.094 3.031,0.25 0.177,0.156 10 false 1 2.396,1.885 2.688,2.063 0.292,0.177 10 false FL- 2.854,2.24 3.021,2.438 0.167,0.198 10 false 2 2.385,2.448 2.677,2.625 0.292,0.177 10 false FL+ 4,2.229 4.135,2.396 0.135,0.167 10 false 2 4,1.656 4.177,1.813 0.177,0.156 10 false 1 2.833,1.667 3.01,1.823 0.177,0.156 10 false 1 6.146,0.313 6.438,0.49 0.292,0.177 10 false FR- 6.156,0.854 6.448,1.031 0.292,0.177 10 false FR+ 6.146,1.875 6.438,2.052 0.292,0.177 10 false FL- 6.167,2.427 6.458,2.604 0.292,0.177 10 false FL+ 5.854,0.167 6.021,0.365 0.167,0.198 10 false 6 5.844,0.74 6.042,0.906 0.198,0.167 10 false 7 5.813,2.313 6.021,2.479 0.208,0.167 10 false 19 5.802,1.74 6.063,1.927 0.26,0.188 10 false 18 2.802,2.448 3.01,2.646 0.208,0.198 10 false p2 3.938,2.458 4.219,2.625 0.281,0.167 10 false Ap2 3.938,0.875 4.208,1.115 0.271,0.24 10 false Ap1 2.833,0.865 3.063,1.125 0.229,0.26 10 false p1 3.063,2.74 5.271,2.917 2.208,0.177 10 false Front Skid Control Sensor Wire LH

CAUTION / NOTICE / HINT

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open circuit detection/ Error or Normal Normal -
FL Speed Open Front speed sensor LH open circuit detection/ Error or Normal Normal -

OK:

Normal (there are no momentary interruptions).


HINT:

Perform the above inspection before removing the sensor and disconnecting the connector.




OK

2.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)

NG

4.INSPECT SKID CONTROL SENSOR WIRE
2.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)

OK

3.RECONFIRM DTC

NG

4.INSPECT SKID CONTROL SENSOR WIRE
3.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

B

4.INSPECT SKID CONTROL SENSOR WIRE
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking parts and connecting parts of the connectors.


c.

Remove the skid control sensor wire (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL).


d.
U148453E07
2.719,1.948 2.823,1.948 2.823,1.948 2.833,1.24 false 2.49,1.167 1.677,1.344 1.677,1.344 1.677,1.458 false 0.115,0.031 0.302,0.229 0.188,0.198 10 false *1 0.563,0.146 0.865,0.354 0.302,0.208 10 false Ap1 2.604,0.427 2.813,0.656 0.208,0.229 10 false p2 1.167,1.531 2.031,1.708 0.865,0.177 10 false FR-*A, FL-*B 1.688,1.844 2.615,2.021 0.927,0.177 10 false FR+*A, FL+*B 2.604,0.146 2.802,0.375 0.198,0.229 10 false p1 0.552,0.438 0.865,0.656 0.313,0.219 10 false Ap2 0.938,0.083 1.125,0.24 0.188,0.156 10 false *A 0.938,0.385 1.125,0.542 0.188,0.156 10 false *B 2.927,0.083 3.115,0.24 0.188,0.156 10 false *A 2.917,0.385 3.104,0.542 0.188,0.156 10 false *B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
Ap1-1 - p1-1 (FR-) Always Below 1 Ω
Ap1-2 - p1-2 (FR+) Always Below 1 Ω
Ap1-1 - Ap1-2 Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
Ap2-1 - p2-1 (FL-) Always Below 1 Ω
Ap2-2 - p2-2 (FL+) Always Below 1 Ω
Ap2-1 - Ap2-2 Always 10 kΩ or higher


Text in Illustration
*A for RH
*B for LH
*1 Skid Control Sensor Wire



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
a.

Install the skid control sensor wire.


b.

Disconnect the A6 skid control ECU connector.


c.

Disconnect the p1 and/or p2 speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A6-7 (FR+) - p1-2 (FR+) Always Below 1 Ω
A6-7 (FR+) - Body ground Always 10 kΩ or higher
A6-6 (FR-) - p1-1 (FR-) Always Below 1 Ω
A6-6 (FR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A6-19 (FL+) - p2-2 (FL+) Always Below 1 Ω
A6-19 (FL+) - Body ground Always 10 kΩ or higher
A6-18 (FL-) - p2-1 (FL-) Always Below 1 Ω
A6-18 (FL-) - Body ground Always 10 kΩ or higher




OK

6.CHECK TERMINAL VOLTAGE (FR+, FL+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (FR+, FL+)
a.

Connect the A6 skid control ECU connector.


b.

Disconnect the p1 and/or p2 speed sensor connector.


c.
U148290E01
0.071,0.103 0.301,0.296 0.230,0.193 10 *a 1.572,0.111 1.756,0.273 0.184,0.163 10 p1 1.568,0.403 1.752,0.566 0.184,0.163 10 p2 1.908,0.028 2.095,0.187 0.187,0.159 10 *A 1.908,0.355 2.095,0.514 0.187,0.159 10 *B 2.552,1.392 3.055,1.733 0.503,0.341 10 FR+*A, FL+*B 1.899,1.174 2.81,1.289 2.81,1.289 2.81,1.392 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
p1-2 (FR+) - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
p2-2 (FL+) - Body ground Ignition switch ON 8 to 14 V


Text in Illustration
*A for RH
*B for LH
*a Front view of wire harness connector
(to Front Speed Sensor)



OK

NG