Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  C1407  Open or Short in Rear Speed Sensor RH Circuit  C1408  Open or Short in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1401 and C1402 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>C1401).

DTC Code DTC Detection Condition Trouble Area
C1407
C1408
Either condition is met:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor RH/LH

·

Skid control sensor wire

·

Speed sensor circuit

·

Brake actuator assembly (Skid control ECU)



HINT:
·

DTC C1407 is for the rear speed sensor RH.

·

DTC C1408 is for the rear speed sensor LH.



WIRING DIAGRAM

C217557E32
5.552,2.708 5.792,2.854 0.24,0.146 10 false A6 5.552,2.917 7.156,3.292 1.604,0.375 10 false Brake Actuator Assembly (Skid Control ECU) 3.125,2.771 5.146,2.948 2.021,0.177 10 false Rear Skid Control Sensor Wire 3.927,0.313 4.24,0.583 0.313,0.271 10 false Sq1 3.927,1.896 4.229,2.135 0.302,0.24 10 false Sq1 2.823,0.313 3.073,0.563 0.25,0.25 10 false q1 2.802,1.875 3.031,2.125 0.229,0.25 10 false q2 0.479,0.573 2.021,0.781 1.542,0.208 10 false Rear Speed Sensor RH 0.5,2.188 2.042,2.396 1.542,0.208 10 false Rear Speed Sensor LH 2.406,0.875 2.698,1.052 0.292,0.177 10 false RR- 2.854,0.083 2.958,0.229 0.104,0.146 10 false 2 2.396,0.323 2.708,0.5 0.313,0.177 10 false RR+ 4,0.135 4.135,0.302 0.135,0.167 10 false 4 4,0.667 4.177,0.823 0.177,0.156 10 false 3 2.844,0.615 3.021,0.771 0.177,0.156 10 false 1 2.385,2.438 2.677,2.615 0.292,0.177 10 false RL- 2.854,1.646 2.969,1.802 0.115,0.156 10 false 2 2.396,1.865 2.688,2.042 0.292,0.177 10 false RL+ 4,1.646 4.135,1.813 0.135,0.167 10 false 2 3.99,2.208 4.167,2.365 0.177,0.156 10 false 1 2.833,2.229 2.938,2.385 0.104,0.156 10 false 1 6.167,0.865 6.458,1.042 0.292,0.177 10 false RR- 6.167,0.313 6.542,0.49 0.375,0.177 10 false RR+ 6.167,2.417 6.458,2.594 0.292,0.177 10 false RL- 6.167,1.865 6.458,2.042 0.292,0.177 10 false RL+ 5.802,0.198 6,0.396 0.198,0.198 10 false 17 5.792,0.729 5.99,0.896 0.198,0.167 10 false 16 5.885,1.74 6.01,1.906 0.125,0.167 10 false 5 5.875,2.292 6.021,2.479 0.146,0.188 10 false 4 2.802,2.438 3.073,2.729 0.271,0.292 10 false q2 3.927,2.458 4.208,2.677 0.281,0.219 10 false Sq1 2.833,0.854 3.073,1.083 0.24,0.229 10 false q1 3.938,0.875 4.219,1.115 0.281,0.24 10 false Sq1

CAUTION / NOTICE / HINT

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open circuit detection/ Error or Normal Normal -
RL Speed Open Rear speed sensor LH open circuit detection/ Error or Normal Normal -

OK:

Normal (there are no momentary interruptions).


HINT:

Perform the above inspection before removing the sensor and disconnecting the connector.




OK

2.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)

NG

4.INSPECT SKID CONTROL SENSOR WIRE
2.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)

OK

3.RECONFIRM DTC

NG

4.INSPECT SKID CONTROL SENSOR WIRE
3.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

B

4.INSPECT SKID CONTROL SENSOR WIRE
U148452E01
0.057,0.026 0.247,0.188 0.191,0.163 10 *1 5.818,0.887 6.002,1.040 0.184,0.152 10 q1 1.176,0.851 1.360,1.003 0.184,0.152 10 q2 6.085,0.786 6.309,0.973 0.224,0.187 10 *A 1.433,0.73 1.672,0.913 0.239,0.184 10 *B 3.453,0.71 3.727,0.863 0.274,0.152 10 Sq1 1.666,2.099 2.003,2.262 0.336,0.163 10 RL+ 0.711,2.089 1.048,2.252 0.336,0.163 10 RL- 6.297,2.11 6.633,2.273 0.336,0.163 10 RR+ 5.337,2.11 5.674,2.273 0.336,0.163 10 RR- 1.125,1.549 0.803,1.942 0.803,1.942 0.803,2.04 false 1.431,1.562 1.776,1.935 1.776,1.935 1.778,2.032 false 5.758,1.577 5.436,1.969 5.436,1.969 5.436,2.068 false 6.065,1.59 6.41,1.962 6.41,1.962 6.412,2.06 false

Text in Illustration
*A for RH *B for LH
*1 Skid Control Sensor Wire - -

a.

Make sure that there is no looseness at the locking parts and connecting parts of the connectors.


b.

Remove the skid control sensor wire (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
Sq1-4 - q1-2 (RR+) Always Below 1 Ω
Sq1-3 - q1-1 (RR-) Always Below 1 Ω
Sq1-4 - Sq1-3 Always 10 kΩ or higher
Sq1-4 - Sq1-1 Always 10 kΩ or higher
Sq1-4 - Sq1-2 Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
Sq1-2 - q2-2 (RL+) Always Below 1 Ω
Sq1-1 - q2-1 (RL-) Always Below 1 Ω
Sq1-2 - Sq1-1 Always 10 kΩ or higher
Sq1-2 - Sq1-3 Always 10 kΩ or higher
Sq1-2 - Sq1-4 Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
a.

Install the skid control sensor wire.


b.

Disconnect the A6 skid control ECU connector.


c.

Disconnect the q1 and/or q2 speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A6-17 (RR+) - q1-2 (RR+) Always Below 1 Ω
A6-17 (RR+) - Body ground Always 10 kΩ or higher
A6-16 (RR-) - q1-1 (RR-) Always Below 1 Ω
A6-16 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A6-5 (RL+) - q2-2 (RL+) Always Below 1 Ω
A6-5 (RL+) - Body ground Always 10 kΩ or higher
A6-4 (RL-) - q2-1 (RL-) Always Below 1 Ω
A6-4 (RL-) - Body ground Always 10 kΩ or higher




OK

6.CHECK TERMINAL VOLTAGE (RR+, RL+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (RR+, RL+)
a.

Connect the A6 skid control ECU connector.


b.

Disconnect the q1 and/or q2 speed sensor connector.


c.
U148291E01
0.071,0.103 0.301,0.296 0.230,0.193 10 *a 1.572,0.111 1.756,0.273 0.184,0.163 10 q1 1.568,0.403 1.752,0.566 0.184,0.163 10 q2 1.908,0.028 2.095,0.187 0.187,0.159 10 *A 1.908,0.355 2.095,0.514 0.187,0.159 10 *B 2.552,1.392 3.055,1.733 0.503,0.341 10 RR+*A, RL+*B 1.899,1.174 2.81,1.289 2.81,1.289 2.81,1.392 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
q1-2 (RR+) - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
q2-2 (RL+) - Body ground Ignition switch ON 8 to 14 V


Text in Illustration
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)



OK

NG