Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  C1432  Steering Angle Sensor Power Source Voltage Malfunction  


DESCRIPTION

Signals from the steering angle sensor (built into the spiral cable) are sent to the skid control ECU (built into the brake actuator assembly) through CAN communication.

DTC Code DTC Detection Condition Trouble Area
C1432 A steering angle sensor power supply malfunction signal is received from the steering angle sensor.
·

ECU-B fuse

·

ECU-IG NO. 1 fuse

·

Steering angle sensor power supply

·

Steering angle sensor circuit

·

Steering angle sensor (Spiral cable sub-assembly)



WIRING DIAGRAM

C200080E34
3.938,0.813 4.792,1.01 0.854,0.198 10 false from Battery 3.927,1.458 5.333,1.646 1.406,0.188 10 false from IG1 Circuit 0.896,0.802 1.198,0.99 0.302,0.188 10 false BAT 1.01,1.417 1.198,1.583 0.188,0.167 10 false IG 0.875,1.75 1.24,1.938 0.365,0.188 10 false ESS 1.323,0.667 1.563,0.865 0.24,0.198 10 false 6 1.323,1.313 1.542,1.51 0.219,0.198 10 false 5 1.323,1.656 1.5,1.813 0.177,0.156 10 false 2 0.229,2.573 3.531,2.781 3.302,0.208 10 false Steering Angle Sensor (Spiral Cable Sub-assembly) 0.865,3.469 2.802,3.667 1.938,0.198 10 false : CAN Communication System 5.51,2.26 7.094,2.656 1.583,0.396 10 false Brake Actuator Assembly (Skid Control ECU) 5.51,2.073 6.469,2.271 0.958,0.198 10 false A6 0.229,2.375 0.531,2.542 0.302,0.167 10 false G33 2.073,1.604 3.01,1.771 0.938,0.167 10 false ECU-IG NO. 1 2.25,0.958 2.729,1.146 0.479,0.188 10 false ECU-B

CAUTION / NOTICE / HINT

NOTICE:
·

Do not remove the steering angle sensor from the spiral cable sub-assembly.

·

When replacing the spiral cable sub-assembly, confirm that the replacement part is of the correct specification.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When DTC U0073, U0123, U0124 and/or U0126 is output together with DTC C1432, inspect and repair the trouble areas indicated by DTC U0073, U0123, U0124 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>U0073).

·

When the speed sensor or the yaw rate and acceleration sensor has trouble, DTCs for the steering angle sensor may be stored even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor first, and then inspect and repair the steering angle sensor.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (BAT)
a.

Make sure that there is no looseness at the locking parts and connecting parts of the connectors.


b.

Disconnect the G33 steering angle sensor connector.


c.
U148212E01
0.163,0.094 0.381,0.284 0.218,0.191 10 *a 2.383,1.375 2.671,1.763 false 2.705,1.734 3.191,1.885 0.486,0.151 10 BAT 0.466,1.036 0.774,1.206 0.309,0.170 10 G33

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G33-6 (BAT) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor)



OK

2.CHECK TERMINAL VOLTAGE (IG)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (IG)
a.

Disconnect the G33 steering angle sensor connector.


b.
U148211E01
0.163,0.094 0.381,0.284 0.218,0.191 10 *a 2.133,1.375 1.834,1.763 false 1.571,1.734 1.895,1.885 0.324,0.151 10 IG 0.465,1.068 0.763,1.224 0.298,0.156 10 G33

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G33-5 (IG) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor)



OK

3.CHECK HARNESS AND CONNECTOR (ESS CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ESS CIRCUIT)
a.

Disconnect the G33 steering angle sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-2 (ESS) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR