Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  C1421  Open or Short in Master Cylinder Pressure Sensor  C1281  Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC)  C1423  Master Cylinder Pressure Sensor Zero Point Low Malfunction  C1424  Master Cylinder Pressure Sensor Output Malfunction  


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU in the brake actuator assembly.

C106656E60
4.229,0.25 5.875,0.448 1.646,0.198 10 false Brake Actuator Assembly 2.885,1.031 4.073,1.26 1.188,0.229 10 false Skid Control ECU 5.375,2.417 6.5,3.063 1.125,0.646 10 false Master Cylinder Pressure Sensor 0.188,1.958 1.344,2.219 1.156,0.26 10 false from IG1 Circuit 0.344,2.563 1.323,3.042 0.979,0.479 10 false from Stop Light Switch 0.313,3.375 1.438,3.677 1.125,0.302 10 false to Body Ground 2.76,1.958 3.302,2.292 0.542,0.333 10 false IG1 2.76,2.656 3.333,2.99 0.573,0.333 10 false STP 2.76,3.354 3.427,3.667 0.667,0.313 10 false GND 3.813,1.969 4.375,2.302 0.563,0.333 10 false VCM 3.823,2.667 4.406,3 0.583,0.333 10 false PMC 3.927,3.365 4.323,3.646 0.396,0.281 10 false E2 0.542,4.354 4.938,4.656 4.396,0.302 10 false VCM: Power Supply for Master Cylinder Pressure Sensor 0.542,4.75 4.073,5.042 3.531,0.292 10 false PMC: Master Cylinder Pressure Sensor Input 0.677,5.115 4.281,5.448 3.604,0.333 10 false E2: Master Cylinder Pressure Sensor Ground

DTC Code DTC Detection Condition Trouble Area
C1421 Either condition is met:
1.

With the IG1 terminal voltage between 9.5 and 17.4 V, the VCM terminal voltage is not between 4.4 and 5.6 V for 1.2 seconds or more.

2.

When the VCM terminal voltage is between 4.8 and 5.2 V, the PMC terminal voltage is not between 0.19 and 4.57 V for 1.2 seconds or more.


Brake actuator assembly (Master cylinder pressure sensor)
C1281 Stored only during test mode. Brake actuator assembly (Master cylinder pressure sensor)
C1423 The PMC terminal voltage is below 0.27 V for 5 seconds or more. Brake actuator assembly (Master cylinder pressure sensor)
C1424 One of the following conditions is met:
1.

Noise occurs in the PMC terminal signal 7 times or more within 5 seconds.

2.

When the vehicle speed drops from 40 km/h (25 mph) to 10 km/h (6 mph), the master cylinder pressure does not change by at least 0.048 MPa.

3.

At a vehicle speed of 7 km/h (4.3 mph) or more, the PMC terminal voltage is between 0.86 and 1.0 V and the master cylinder pressure does not change by at least 0.048 MPa for 60 seconds or more.

4.

At a vehicle speed of 7 km/h (4 mph) or more, the PMC terminal voltage is 1.0 V or more and the master cylinder pressure does not change by at least 0.048 MPa for 30 seconds or more.

5.

At a vehicle speed of 7 km/h (4 mph) or more with the stop switch on, a state in which the pressure sensor input value is sufficiently more than the estimated master pressure continues for 1 second or more and this state occurs 5 or more times each time the ignition switch is turned to ON, and this occurs 8 or more times consecutively.


Brake actuator assembly (Master cylinder pressure sensor)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CALIBRATION).


PROCEDURE

1.REPLACE BRAKE ACTUATOR ASSEMBLY
a.

Replace the brake actuator assembly (master cylinder pressure sensor) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL).



NEXT

END