Home › Brake › PARKING BRAKE › PARKING BRAKE ASSEMBLY
RM27T0E _54 Brake _053716 PARKING BRAKE _0260942 PARKING BRAKE ASSEMBLY A

PARKING BRAKE  PARKING BRAKE ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 47447E 1.INSTALL PARKING BRAKE SHOE HOLD DOWN SPRING PIN

a.

Install the parking brake shoe hold down spring pin (for front side).


b.

Install the parking brake shoe hold down spring pin (for rear side).


Hide 2.APPLY HIGH-TEMPERATURE GREASE

a.
C217133E01
0.583,1.828 0.787,1.977 0.205,0.149 10 *1

Apply a light coat of high-temperature grease to the areas of the backing plate which make contact with the shoe as shown in the illustration.

Text in Illustration
*1 High temperature grease


Hide 47612 3.INSTALL PARKING BRAKE SHOE LEVER LH

a.

Apply a light coat of high-temperature grease to the areas of the parking brake shoe lever which make contact with the No. 2 parking brake shoe assembly.


b.
C217112

Install the parking brake shoe lever and shim to the No. 2 parking brake shoe assembly with a new C-washer as shown in the illustration.


c.
C132648

Using a feeler gauge, measure the clearance between the No. 2 parking brake shoe assembly and parking brake shoe lever.

Standard clearance:

Less than 0.25 mm (0.00984 in.)

If the clearance is not within the specification, replace the shim with one of a different thickness so that the clearance is within the specification.


Standard Shim:
Shim Thickness Shim Thickness
0.2 mm (0.00787 in.) 0.5 mm (0.0197 in.)
0.3 mm (0.0118 in.) 0.6 mm (0.0236 in.)
0.4 mm (0.0157 in.) 0.9 mm (0.0354 in.)



Hide 46590 4.INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY WITH PARKING BRAKE SHOE LEVER

a.
C217113

Using needle-nose pliers, connect the No. 3 parking brake cable assembly to the parking brake shoe lever as shown in the illustration.

NOTICE:

Be careful not to damage the No. 3 parking brake cable assembly.



Hide 46550A 5.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING

a.

Install the parking brake shoe return tension spring to the No. 2 parking brake shoe assembly.


Hide 46580 6.INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH

a.

Connect the parking brake shoe return tension spring to install the No. 1 parking brake shoe assembly.


Hide 47406A 7.INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET

a.
C191831E04
0.656,4.208 0.844,4.385 0.188,0.177 10 false *1

Apply a light coat of high-temperature grease to the areas of the shoe adjusting screw set shown in the illustration.

Text in Illustration
*1 High-temperature grease


b.

Install the parking brake shoe adjusting screw set.


Hide 46590 8.INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH

a.

Install the No. 2 parking brake shoe assembly to the backing plate with the parking brake shoe hold down spring cups and parking brake shoe hold down spring.


Hide 47614 9.INSTALL PARKING BRAKE SHOE STRUT LH

a.

Install the parking brake shoe strut and parking brake shoe strut compression spring.


Hide 46580 10.INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH

a.

Install the No. 1 parking brake shoe assembly to the backing plate with the parking brake shoe hold down spring cups and parking brake shoe hold down spring.


Hide 46550E 11.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING

a.

Install the 2 parking brake shoe return tension spring.

HINT:

First install the front side spring, and then the rear side spring.



Hide 12.CHECK PARKING BRAKE INSTALLATION

C354132E01
1.333,3.375 1.5,3.542 0.167,0.167 10 false *a 5.667,3.375 5.833,3.542 0.167,0.167 10 false *a 1.75,0.083 1.917,0.25 0.167,0.167 10 false *A 5.25,0.083 5.417,0.25 0.167,0.167 10 false *B

a.

Check that each part is installed properly.

Text in Illustration
*A LH *B RH
*a Front - -

NOTICE:

There should be no oil or grease adhering to the friction surfaces of the shoe lining and disc.



Hide 42431 13.INSTALL REAR DISC

Hide 14.CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH

a.

Connect the rear disc brake cylinder with the 2 bolts.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


Hide 15.INSPECT PARKING BRAKE LEVER TRAVEL

Hide 16.ADJUST PARKING BRAKE LEVER TRAVEL

Hide 17.INSTALL REAR WHEEL LH

Torque:
for Aluminum Wheel : 103 N*m (1050 kgf*cm, 76 ft.*lbf)
for Steel Wheel : 112 N*m (1137 kgf*cm, 82 ft.*lbf)