Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP (for 2TR-FE)
RM27T0E _55 Steering _053717 POWER ASSIST SYSTEMS _0260948 VANE PUMP(for 2TR-FE) A

POWER ASSIST SYSTEMS  VANE PUMP(for 2TR-FE)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

When installing the parts indicated by arrows, coat them with power steering fluid (See page Steering>POWER ASSIST SYSTEMS>VANE PUMP (for 2TR-FE)>COMPONENTS).


PROCEDURE

Hide 1.INSTALL VANE PUMP HOUSING OIL SEAL

a.

Coat the lip of a new vane pump housing oil seal with power steering fluid.


b.
G036583E04
2.49,0.604 2.75,0.625 false 2.75,0.625 2.604,0.917 false 2.802,0.521 3.125,0.688 0.323,0.167 10 false SST

Using SST and a press, press in the oil seal.

SST
09950-60010  (09951-00280)
09950-70010  (09951-07100)

NOTICE:
·

Make sure to install the oil seal so that it is facing in the correct direction.

·

Be careful not to damage the oil seal.




Hide 2.INSTALL SHAFT WITH PULLEY

a.

Coat the shaft with power steering fluid.


b.
F051464E04
1.698,1.073 1.438,0.26 1.438,0.26 1.198,0.26 false 0.99,0.167 1.292,0.427 0.302,0.26 10 false *1

Gradually insert the vane pump shaft with vane pump pulley.

Text in Illustration
*1 Protective Tape

NOTICE:
·

Do not damage the lip of the oil seal in the vane pump front housing.

·

Wrap protective tape around the spline of the vane pump shaft with vane pump pulley in order to prevent damage to the oil seal.




Hide 3.INSTALL FRONT VANE PUMP SIDE PLATE

a.

Coat a new No. 2 O-ring with power steering fluid.


b.
C065369

Install the No. 2 O-ring to the front housing.


c.

Coat a new No. 1 O-ring with power steering fluid.


d.
C359219

Install the No. 1 O-ring to the front side plate.


e.
F050370

Install the front side plate to the front housing while aligning the semicircle-shaped cutouts of both parts.

NOTICE:

Be sure to install the plate in the correct position and so that it is facing the correct direction.



Hide 4.INSTALL VANE PUMP CAM RING

a.
F050371E08
0.906,0.667 0.531,0.292 0.531,0.292 0.417,0.292 true 0.219,0.219 0.406,0.385 0.188,0.167 10 false *a

With the inscribed mark facing upward, install the vane pump cam ring to the vane pump front housing while aligning the semicircle-shaped cutouts of both parts.

Text in Illustration
*a Inscribed Mark

NOTICE:

Be sure to install the cam ring in the correct position and so that it is facing the correct direction.



Hide 5.INSTALL VANE PUMP ROTOR

a.
C095038

Install the vane pump rotor to the front vane pump housing.

HINT:

The vane pump can be installed with either side facing up.



b.

Coat the 10 vane pump plates with power steering fluid.


c.
U149170E05
0.927,0.375 1.083,0.375 1.083,0.375 1.24,0.781 false 0.552,1.25 1.115,1.417 0.563,0.167 10 false *b 2.656,0.177 3.115,0.333 0.458,0.156 10 false *c 0.719,0.281 1.458,0.427 0.74,0.146 10 false *a

Install the 10 vane pump plates.

Text in Illustration
*a Round End
*b Outward
*c Inward

NOTICE:

Make sure that the round ends of the vane pump plates are facing outward.



Hide 6.INSTALL VANE PUMP SHAFT SNAP RING

a.
F051011

Using a screwdriver and snap ring expander, install a new snap ring to the shaft with pulley.


Hide 7.INSTALL REAR VANE PUMP HOUSING

a.
F050373

Coat a new O-ring with power steering fluid and install it to the rear housing.


b.

Align the straight pin of the rear housing with the hole created by the semicircle-shaped cutouts of the cam ring, front side plate and front housing. Then install the rear housing with the 4 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)

NOTICE:

Make sure that the O-ring is not out of position before installing the rear vane pump housing.



Hide 9.INSPECT TOTAL PRELOAD

a.
C053369

Check that the pump rotates smoothly without abnormal noise.


b.

Temporarily install a service bolt.

Recommended Service Bolt:
Item Specified Condition
Thread diameter 10 mm (0.394 in.)
Thread pitch 1.25 mm (0.0492 in.)
Bolt length 50 mm (1.97 in.)



c.

Using a torque wrench, check the pump rotating torque.

Standard Rotating torque:

0.3 N*m (3 kgf*cm, 2 in.*lbf) or less


If the rotating torque is not as specified, check the installation of the housing oil seal.


Hide 89438A 10.INSTALL POWER STEERING OIL PRESSURE SWITCH (w/o VSC)

a.

Coat a new O-ring with power steering fluid and install it to the oil pressure switch.


b.

Install the oil pressure switch to the vane pump.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 44308A 11.INSTALL PRESSURE PORT UNION O-RING (w/o VSC)

a.

Coat the compression spring and flow control valve with power steering fluid.


b.

Install the compression spring.


c.

Install the flow control valve facing in the correct direction.


d.

Coat a new O-ring with power steering fluid and install it onto the pressure port union.


e.

Install the pressure port union.

Torque:
69 N*m (704 kgf*cm, 51 ft.*lbf)


Hide 44306 12.INSTALL VANE PUMP OIL RESERVOIR SUB-ASSEMBLY

a.

Coat a new O-ring with power steering fluid and install it to the vane pump reservoir.


b.

Install the vane pump reservoir to the vane pump with the 3 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 44305 13.INSTALL VANE PUMP OIL RESERVOIR CAP SUB-ASSEMBLY

a.

Install the vane pump oil reservoir cap sub-assembly