Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › 2015.06–2017.08
RM27T0E _55 Steering _053718 STEERING COLUMN _0260955 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2610  Tilt Position Sensor or Tilt Motor Circuit Malfunction  


DESCRIPTION

The tilt motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and tilts the steering column up and down. The tilt position sensor (Hall IC) in the tilt motor detects the tilt angle of the steering column and outputs a signal to the multiplex tilt and telescopic ECU based on that angle.

HINT:

The limit positions can be confirmed on the Data List screen of the intelligent tester.


DTC Code Detection Condition Trouble Area
B2610 The tilt operation stops within the operation range while operating.
·

Harness or connector

·

Tilt position sensor or tilt motor

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C200408E01
0.949,1.019 1.556,1.161 0.607,0.142 10 Tilt Motor 2.128,0.395 2.902,0.537 0.774,0.142 10 from Battery 3.466,0.529 3.976,0.671 0.510,0.142 10 TI & TE 4.619,4.084 5.122,4.226 0.503,0.142 10 G116 4.642,0.413 4.937,0.555 0.295,0.142 10 +B 5.98,0.548 6.275,0.690 0.295,0.142 10 +B 5.98,1.347 6.275,1.489 0.295,0.142 10 +B 6.113,2.151 6.470,2.293 0.357,0.142 10 12 V 5.961,3.263 6.443,3.405 0.482,0.142 10 to CPU 4.642,0.925 4.999,1.067 0.357,0.142 10 TIM+ 4.642,2.473 4.999,2.615 0.357,0.142 10 VCI 4.642,2.872 4.909,3.014 0.267,0.142 10 TIS 4.642,3.658 4.999,3.800 0.357,0.142 10 GND 4.619,4.251 6.723,4.421 2.104,0.170 10 Multiplex Tilt and Telescopic ECU 4.642,3.257 4.853,3.399 0.211,0.142 10 E1 4.642,1.719 4.999,1.861 0.357,0.142 10 TIM- 4.454,0.508 4.562,0.650 0.107,0.142 10 2 4.454,1.724 4.562,1.866 0.107,0.142 10 1 4.454,2.477 4.562,2.619 0.107,0.142 10 6 4.454,2.875 4.562,3.017 0.107,0.142 10 7 4.411,0.934 4.594,1.076 0.184,0.142 10 10 4.411,3.274 4.594,3.416 0.184,0.142 10 17 4.422,3.675 4.606,3.817 0.184,0.142 10 11 0.44,3.344 1.672,3.486 1.232,0.142 10 Tilt Position Sensor 0.795,4.218 1.193,4.360 0.398,0.142 10 G122 0.795,4.353 1.435,4.495 0.640,0.142 10 Tilt Motor 1.705,0.926 2.055,1.068 0.350,0.142 10 TIM+ 2.088,0.933 2.198,1.075 0.111,0.142 10 1 1.705,1.731 2.055,1.873 0.350,0.142 10 TIM- 2.093,1.739 2.204,1.881 0.111,0.142 10 2 1.762,2.467 2.055,2.609 0.294,0.142 10 VCI 2.093,2.467 2.204,2.609 0.111,0.142 10 4 1.775,2.877 2.024,3.019 0.250,0.142 10 TIS 2.093,2.877 2.204,3.019 0.111,0.142 10 5 1.827,3.262 2.025,3.404 0.198,0.142 10 E1 2.093,3.262 2.204,3.404 0.111,0.142 10 6

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TILT OPERATION)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the steering wheel tilts up and down.

Tilt & Telescopic
Tester Display Test Part Control Range Diagnostic Note
Tilt Operation Tilt operation UP/DOWN -

Result
Result Proceed to
Steering wheel does not tilt up/down. A
Steering wheel tilts up/down. B



A

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)

B

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)
a.
U148220E03
2.01,1.479 1.625,1.719 true 0.167,0.042 0.354,0.24 0.188,0.198 10 false *a 1.24,1.76 1.677,1.958 0.438,0.198 10 false 2 (+B) 2.083,0.208 2.469,0.385 0.385,0.177 10 false G116

Disconnect the G116 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G116-2 (+B) - Body ground Always 11 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)



OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
U148221E03
2.01,1.396 1.625,1.719 true 0.229,0.063 0.417,0.26 0.188,0.198 10 false *a 1.24,1.76 1.917,1.958 0.677,0.198 10 false 11 (GND) 2.094,0.229 2.479,0.406 0.385,0.177 10 false G116

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G116-11 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)



OK

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR)
a.

Disconnect the G122 tilt motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G116-10 (TIM+) - G122-1 (TIM+) Always Below 1 Ω
G116-1 (TIM-) - G122-2 (TIM-)
G116-10 (TIM+) - Body ground Always 10 kΩ or higher
G116-1 (TIM-) - Body ground




OK

5.CHECK TILT MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TILT MOTOR
U115808E01
0.305,0.226 0.508,0.414 0.204,0.188 10 *a 2.069,1.112 2.386,0.666 false 2.069,1.112 2.386,0.666 false 2.452,0.555 2.800,0.740 0.348,0.185 10 TIM+ 1.358,1.131 1.042,0.686 false 1.358,1.131 1.042,0.686 false 0.584,0.555 0.932,0.740 0.348,0.185 10 TIM-

a.

Apply 12 V battery voltage to the tilt motor connector. Then check the steering wheel tilt operation.

OK:
Measurement Condition Specified Condition
12 V battery positive (+) lead → Terminal 1 (TIM+)
12 V battery negative (-) lead → Terminal 2 (TIM-)
The steering wheel tilts up.
12 V battery positive (+) lead → Terminal 2 (TIM-)
12 V battery negative (-) lead → Terminal 1 (TIM+)
The steering wheel tilts down.


Text in Illustration
*a Component without harness connected
(Tilt Motor)



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR)
a.

Disconnect the G116 multiplex tilt and telescopic ECU connector.


b.

Disconnect the G122 tilt motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G116-6 (VCI) - G122-4 (VCI) Always Below 1 Ω
G116-7 (TIS) - G122-5 (TIS)
G116-17 (E1) - G122-6 (E1)
G116-6 (VCI) - Body ground Always 10 kΩ or higher
G116-7 (TIS) - Body ground
G116-17 (E1) - Body ground




OK

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
U148222E03
2.01,1.406 1.625,1.719 true 0.229,0.063 0.417,0.26 0.188,0.198 10 false *a 1.24,1.76 1.917,1.958 0.677,0.198 10 false 11 (GND) 2.115,0.24 2.5,0.417 0.385,0.177 10 false G116

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G116-11 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)



OK

8.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI TERMINAL VOLTAGE)
a.
U149174E01
1.071,1.949 1.421,2.115 0.350,0.165 10 VCI 2.302,1.949 2.523,2.096 0.221,0.147 10 E1 0.255,0.202 0.434,0.394 0.179,0.192 10 *a 1.618,1.617 1.28,1.92 false 2.095,1.628 2.409,1.949 false 1.618,1.617 1.28,1.92 false 2.095,1.628 2.409,1.949 false 1.531,0.518 1.915,0.693 0.385,0.174 10 G122

Reconnect the G116 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G122-4 (VCI) - G122-6 (E1) Engine switch on (IG) 8 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Tilt Motor)



OK

9.CHECK TILT POSITION SENSOR

NG

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

9.CHECK TILT POSITION SENSOR
a.
U148219E03
2.479,0.969 2.792,0.479 true 2.406,1.042 3.042,1.625 true 0.229,0.094 0.427,0.271 0.198,0.177 10 false *a 2.781,0.292 3.271,0.469 0.49,0.177 10 false 17 (E1) 2.833,1.667 3.292,1.844 0.458,0.177 10 false 7 (TIS) 2.094,0.448 2.479,0.625 0.385,0.177 10 false G116

Reconnect the G122 tilt motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G116-7 (TIS) - G116-17 (E1) Steering tilting up or tilting down Pulse generation
High: 8 to 14 V
Low: Below 1 V


Text in Illustration
*a Component with harness connected
(Multiplex Tilt and Telescopic ECU)



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)