Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260967 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

Using this circuit, the radio receiver assembly sends power to the telephone microphone assembly, and the telephone microphone assembly sends microphone signals to the radio receiver assembly.

WIRING DIAGRAM

E284353E02
0.531,2.698 2.344,2.896 1.813,0.198 10 false Map Light Assembly 0.781,0.625 1.552,1.313 0.771,0.688 10 false Telephone Microphone Assembly 1.802,0.833 2.229,0.99 0.427,0.156 10 false MCO+ 1.844,1.229 2.26,1.385 0.417,0.156 10 false MCO- 1.792,0.406 2.24,0.563 0.448,0.156 10 false MACC 4.458,1.865 5.073,2.021 0.615,0.156 10 false Shielded 3.667,1.865 4.281,2.021 0.615,0.156 10 false Shielded 2.885,1.854 3.5,2.01 0.615,0.156 10 false Shielded 2.313,2.021 2.563,2.177 0.25,0.156 10 false 14 2.313,0.844 2.521,1 0.208,0.156 10 false 12 2.313,1.229 2.521,1.385 0.208,0.156 10 false 13 2.313,0.427 2.563,0.583 0.25,0.156 10 false 11 5.479,2.031 5.604,2.188 0.125,0.156 10 false 6 5.396,1.625 5.583,1.781 0.188,0.156 10 false 18 5.469,0.844 5.583,1 0.115,0.156 10 false 5 5.396,1.229 5.583,1.385 0.188,0.156 10 false 19 5.469,0.427 5.594,0.583 0.125,0.156 10 false 4 5.604,2.677 6.708,3.031 1.104,0.354 10 false Radio Receiver Assembly 0.531,2.5 1.01,2.708 0.479,0.208 10 false W7 5.604,2.5 6.031,2.677 0.427,0.177 10 false H47 5.708,0.958 6.146,1.115 0.438,0.156 10 false MIN+ 5.708,1.313 6.146,1.469 0.438,0.156 10 false MIN- 5.708,1.719 6.198,1.875 0.49,0.156 10 false SGND 5.708,0.521 6.146,0.677 0.438,0.156 10 false MACC 1.833,2.021 2.229,2.177 0.396,0.156 10 false SNS2 5.708,2.125 6.146,2.281 0.438,0.156 10 false SNS2

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H47 radio receiver assembly connector.


b.

Disconnect the W7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H47-6 (SNS2) - W7-14 (SNS2) Always Below 1 Ω
H47-4 (MACC) - W7-11 (MACC) Always Below 1 Ω
H47-5 (MIN+) - W7-12 (MCO+) Always Below 1 Ω
H47-19 (MIN-) - W7-13 (MCO-) Always Below 1 Ω
H47-4 (MACC) - Body ground Always 10 kΩ or higher
H47-5 (MIN+) - Body ground Always 10 kΩ or higher
H47-19 (MIN-) - Body ground Always 10 kΩ or higher
H47-18 (SGND) - Body ground Always 10 kΩ or higher




OK

2.CHECK RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK RADIO RECEIVER ASSEMBLY
a.
U170701E02
2.052,1.323 2.167,1.917 2.167,1.917 2.396,1.917 false 2.198,1.302 2.427,1.667 2.427,1.667 2.656,1.667 false 2.167,1.083 2.49,0.396 2.49,0.396 2.719,0.396 false 2.458,1.833 2.823,2.01 0.365,0.177 10 false MIN- 2.698,1.594 3.146,1.771 0.448,0.177 10 false SGND 2.76,0.333 3.208,0.51 0.448,0.177 10 false MACC 0.063,0.042 0.302,0.219 0.24,0.177 10 false *a 0.26,1.031 0.604,1.208 0.344,0.177 10 false H47

Remove the radio receiver assembly with its connectors still connected (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER(for Radio Receiver Type)>REMOVAL).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H47-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H47-18 (SGND) - Body ground Always Below 1 Ω
H47-19 (MIN-) - Body ground Always Below 1 Ω



Text in Illustration
*a Component with harness connected
(Radio Receiver Assembly)


OK

3.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

3.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL).


b.

Check that the malfunction disappears.

OK:

Malfunction disappears.




OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG