Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM › 2015.06–2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260968 REAR SEAT ENTERTAINMENT SYSTEM J

AUDIO / VIDEO  REAR SEAT ENTERTAINMENT SYSTEM  Sound Signal Circuit between Headphone Terminal and Television Display  


DESCRIPTION

This circuit sends a sound signal from the television display to the headphone terminal.

WIRING DIAGRAM

E284348E01
6.135,0.282 6.556,0.460 0.422,0.178 10 HP2R 5.87,0.192 6.062,0.370 0.193,0.178 10 26 6.135,0.723 6.556,0.901 0.422,0.178 10 HP2L 5.87,0.632 6.062,0.810 0.193,0.178 10 28 5.792,3.73 6.214,3.908 0.422,0.178 10 W14 5.792,3.897 6.947,4.268 1.155,0.371 10 Television Display Assembly 0.058,1.482 0.557,1.660 0.499,0.178 10 T4 0.058,1.65 1.632,1.850 1.575,0.200 10 Headphone Terminal LH 0.058,3.699 0.557,3.877 0.499,0.178 10 T2 0.058,3.867 1.632,4.067 1.575,0.200 10 Headphone Terminal RH 0.671,0.282 1.066,0.460 0.395,0.178 10 HP2R 0.685,0.723 1.066,0.901 0.381,0.178 10 HP2L 1.188,0.192 1.312,0.370 0.123,0.178 10 1 1.188,0.632 1.312,0.810 0.123,0.178 10 2 4.26,1.364 4.911,1.542 0.651,0.178 10 Shielded 2.332,1.364 2.983,1.542 0.651,0.178 10 Shielded 6.135,1.163 6.556,1.341 0.422,0.178 10 SLD6 0.651,1.163 1.066,1.341 0.414,0.178 10 SGN2 5.87,1.073 6.062,1.251 0.193,0.178 10 27 1.188,1.073 1.312,1.251 0.123,0.178 10 3 6.135,2.557 6.556,2.735 0.422,0.178 10 HP1R 5.876,2.467 6.062,2.645 0.187,0.178 10 12 6.135,2.998 6.556,3.176 0.422,0.178 10 HP1L 5.876,2.907 6.062,3.085 0.187,0.178 10 14 0.677,2.557 1.066,2.735 0.389,0.178 10 HP1R 0.691,2.998 1.066,3.176 0.375,0.178 10 HP1L 1.188,2.467 1.312,2.645 0.123,0.178 10 1 1.188,2.907 1.312,3.085 0.123,0.178 10 2 4.26,3.639 4.911,3.817 0.651,0.178 10 Shielded 3.254,3.639 3.905,3.817 0.651,0.178 10 Shielded 2.332,3.639 2.983,3.817 0.651,0.178 10 Shielded 6.135,3.438 6.556,3.616 0.422,0.178 10 SLD5 0.669,3.438 1.066,3.616 0.397,0.178 10 SGN1 5.876,3.348 6.062,3.526 0.187,0.178 10 13 1.188,3.348 1.312,3.526 0.123,0.178 10 3

PROCEDURE

1.CHECK HEADPHONES
a.

Check the malfunctioning headphones.

Result
Result Proceed to
Malfunction in headphone terminal LH side A
Malfunction in headphone terminal RH side B



A

2.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - HEADPHONE TERMINAL LH)

B

4.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - HEADPHONE TERMINAL RH)
2.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - HEADPHONE TERMINAL LH)
a.

Disconnect the W14 television display assembly connector.


b.

Disconnect the T4 headphone terminal LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W14-26 (HP2R) - T4-1 (HP2R) Always Below 1 Ω
W14-27 (SLD6) - T4-3 (SGN2) Always Below 1 Ω
W14-28 (HP2L) - T4-2 (HP2L) Always Below 1 Ω
W14-26 (HP2R) - Body ground Always 10 kΩ or higher
W14-27 (SLD6) - Body ground Always 10 kΩ or higher
W14-28 (HP2L) - Body ground Always 10 kΩ or higher




OK

3.CHECK TELEVISION DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TELEVISION DISPLAY ASSEMBLY
a.
U149344E01
0.132,1.56 0.519,1.741 0.387,0.181 10 HP2R 0.077,1.155 0.442,1.336 0.364,0.181 10 HP2L 1.187,1.04 0.77,1.645 0.77,1.645 0.608,1.645 false 0.918,1.042 0.662,1.247 0.662,1.247 0.507,1.247 false 0.046,0 0.434,0.181 0.387,0.181 10 *a 0.26,0.714 0.648,0.896 0.387,0.181 10 W14

Remove the television display assembly connector still connected (See page Audio / Visual / Telematics>AUDIO / VIDEO>TELEVISION DISPLAY>REMOVAL).


b.

Using an oscilloscope, check the waveform between each terminal and the body ground according to the conditions as shown in the table below.

Standard:
Tester Connection Condition Specified Condition
W14-26 (HP2R) - Body ground Audio sound being produced A waveform synchronized with sound is output
W14-28 (HP2L) - Body ground


Text in Illustration
*a Component with harness connected
(Television Display Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE TELEVISION DISPLAY ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - HEADPHONE TERMINAL RH)
a.

Disconnect the W14 television display assembly connector.


b.

Disconnect the T2 headphone terminal RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W14-12 (HP1R) - T2-1 (HP1R) Always Below 1 Ω
W14-13 (SLD5) - T2-3 (SGN1) Always Below 1 Ω
W14-14 (HP1L) - T2-2 (HP1L) Always Below 1 Ω
W14-12 (HP1R) - Body ground Always 10 kΩ or higher
W14-13 (SLD5) - Body ground Always 10 kΩ or higher
W14-14 (HP1L) - Body ground Always 10 kΩ or higher




OK

5.CHECK TELEVISION DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TELEVISION DISPLAY ASSEMBLY
a.
U149345E03
1.188,0.896 1.438,0.156 1.438,0.156 1.615,0.156 true 0.927,0.885 0.698,0.458 0.698,0.458 0.51,0.458 true 1.656,0.073 2.042,0.25 0.385,0.177 10 false HP1R 0.104,0.385 0.469,0.563 0.365,0.177 10 false HP1L 0.094,0.073 0.313,0.25 0.219,0.177 10 false *a 0.24,0.906 0.625,1.083 0.385,0.177 10 false W14

Remove the television display assembly connector still connected (See page Audio / Visual / Telematics>AUDIO / VIDEO>TELEVISION DISPLAY>REMOVAL).


b.

Using an oscilloscope, check the waveform between each terminal and the body ground according to the conditions as shown in the table below.

Standard:
Tester Connection Condition Specified Condition
W14-12 (HP1R) - Body ground Audio sound being produced A waveform synchronized with sound is output
W14-14 (HP1L) - Body ground


Text in Illustration
*a Component with harness connected
(Television Display Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE TELEVISION DISPLAY ASSEMBLY