Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260991 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Vehicle Speed Signal Circuit between Navigation Receiver Assembly and Combination Meter  


DESCRIPTION

The navigation receiver assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective systems based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E280956E38
1.771,1.052 2.083,1.25 0.313,0.198 10 false +S 2.052,0.938 2.365,1.135 0.313,0.198 10 false 32 1.042,1.813 1.354,2.01 0.313,0.198 10 false G6 1.052,2 3.073,2.271 2.021,0.271 10 false Combination Meter Assembly 4.979,0.917 5.292,1.115 0.313,0.198 10 false 17 5.219,1.063 5.74,1.292 0.521,0.229 10 false SPD 5.094,1.844 5.573,2.083 0.479,0.24 10 false H56 5.073,2.01 7,2.219 1.927,0.208 10 false Navigation Receiver Assembly

PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
U149456E03
1.563,1.344 1.073,1.865 true 1.698,0.219 2.031,0.406 0.333,0.188 10 false G6 0.844,1.813 1.177,2 0.333,0.188 10 false +S 2.99,3.594 3.333,3.781 0.344,0.188 10 false GND 1.26,3.854 1.521,4.042 0.26,0.188 10 false (A) 0.031,0.052 0.365,0.24 0.333,0.188 10 false *a

Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal G6-32 (+S) and body ground.


iii.

Turn the engine switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal G6-32 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)




OK

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the H56 navigation receiver assembly connector.


b.

Disconnect the G6 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H56-17 (SPD) - G6-32 (+S) Always Below 1 Ω
H56-17 (SPD) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR