The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.
*1: for Automatic Transmission
*2: for Manual Transmission
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Enter the "Vehicle Signal Check Mode" screen. [Refer to check Vehicle Signal in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>OPERATION CHECK)].
Check that the display changes between ON and OFF according to the shift lever position.
| Shift Lever Position | Display |
|---|---|
| R | ON |
| Except R | OFF |
This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.
OK
NG
Disconnect the radio and display receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H51-2 (REV) - Body ground | Engine switch on (IG), shift lever in R | 7.5 to 14 V |
| H51-2 (REV) - Body ground | Engine switch on (IG), shift lever not in R | Below 1 V |
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Automatic Transmission) | B |
| NG (for Manual Transmission) | C |
A
(See pageAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL)
B
C
Disconnect the H51 radio and display receiver assembly connector.
Disconnect the C159 park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H51-2 (REV) - C159-1 (RL) | Always | Below 1 Ω |
| H51-2 (REV) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C159-2 (RB) - Body ground | Engine switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Park/neutral Position Switch Assembly) |
| Result | Proceed to |
|---|---|
| OK (for A750F Automatic Transmission) | A |
| OK (for AC60F Automatic Transmission) | B |
| NG | C |
A
(See pageDrivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
B
(See pageDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
C
Disconnect the H51 radio and display receiver assembly connector.
Disconnect the C41*1 or C160*2 back-up light switch assembly connector.
*1: for 1GR-FE
*2: for 1KD-FTV and 1GD-FTV
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H51-2 (REV) - C41-1 | Always | Below 1 Ω |
| H51-2 (REV) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H51-2 (REV) - C160-2 | Always | Below 1 Ω |
| H51-2 (REV) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the back-up light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C41-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C160-1 - Body ground | Engine switch on (IG) | 11 to 14 V |
| *A | for 1GR-FE |
| *B | for 1KD-FTV and 1GD-FTV |
| *a | Front view of wire harness connector
(to Back-up Light Switch Assembly) |
OK
NG