Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260992 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter  


DESCRIPTION

The stereo component amplifier assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective systems based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E278018E10
0.671,1.763 1.008,1.926 0.336,0.163 10 G6 0.671,1.931 2.556,2.129 1.885,0.198 10 Combination Meter Assembly 4.965,1.791 5.413,1.954 0.448,0.163 10 H63 4.965,1.959 6.760,2.282 1.795,0.323 10 Stereo Component Amplifier Assembly 4.944,0.947 5.142,1.110 0.198,0.163 10 11 2.079,0.933 2.277,1.096 0.198,0.163 10 32 1.757,1.056 1.989,1.232 0.232,0.177 10 +S 5.182,1.056 5.595,1.232 0.413,0.177 10 SPD

PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
U149456E01
1.649,0.157 1.981,0.340 0.332,0.184 10 G6 0.88,1.815 1.212,1.999 0.332,0.184 10 +S 2.964,3.538 3.306,3.722 0.342,0.184 10 GND 1.256,3.855 1.513,4.038 0.257,0.184 10 (A) 0.033,0.053 0.365,0.237 0.332,0.184 10 *a 1.563,1.275 1.069,1.795 false

Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal G6-32 (+S) and body ground.


iii.

Turn the engine switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal G6-32 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)




OK

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the H63 stereo component amplifier assembly connector.


b.

Disconnect the G6 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H63-11 (SPD) - G6-32 (+S) Always Below 1 Ω
H63-11 (SPD) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR