Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2015.06–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260992 NAVIGATION SYSTEM(for Radio and Display Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  B1532  LVDS Signal Malfunction (from Extension Module)  


DESCRIPTION

The navigation ECU and the radio and display receiver assembly are connected by the LVDS communication line.

This DTC is stored when an LVDS communication error occurs between the navigation ECU and the radio and display receiver assembly.

DTC Code DTC Detection Condition Trouble Area
B1532 When one of the conditions below is met:
·

Video signal (digital) is lost.

·

Navigation ECU is/was not connected while the engine switch is/was on (IG) or (ACC).

·

Communication between the master unit and the navigation ECU is/was not possible when the engine is/was started.


·

Navigation ECU power source circuit

·

LVDS circuit between radio and display receiver assembly and navigation ECU

·

Navigation ECU

·

Radio and display receiver assembly

·

Harness or connector



HINT:
·

Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

·

The radio and display receiver assembly is the master unit.



WIRING DIAGRAM

E276665E32
0.917,2.313 2.135,2.729 1.219,0.417 10 false Radio and Display Receiver Assembly 5.208,2.354 6.292,2.594 1.083,0.24 10 false Navigation ECU 2.198,1.885 2.49,2.104 0.292,0.219 10 false z10 4.802,1.885 5.052,2.104 0.25,0.219 10 false z11 2.198,0.698 2.479,0.906 0.281,0.208 10 false z12 2.198,1.094 2.469,1.313 0.271,0.219 10 false z12 2.198,1.49 2.479,1.698 0.281,0.208 10 false z12 2.271,0.51 2.5,0.698 0.229,0.188 10 false 4 2.26,0.917 2.49,1.104 0.229,0.188 10 false 3 2.26,1.313 2.49,1.5 0.229,0.188 10 false 8 2.26,1.708 2.49,1.896 0.229,0.188 10 false 1 4.813,0.698 5.104,0.927 0.292,0.229 10 false z13 4.885,0.51 5.115,0.698 0.229,0.188 10 false 1 4.885,0.917 5.115,1.104 0.229,0.188 10 false 3 4.885,1.313 5.115,1.5 0.229,0.188 10 false 2 4.875,1.708 5.104,1.896 0.229,0.188 10 false 1 1.781,0.708 2.083,0.927 0.302,0.219 10 false +B2 5.167,0.708 5.563,0.969 0.396,0.26 10 false B+ 1.708,1.094 2.115,1.292 0.406,0.198 10 false ACC2 5.177,1.083 5.583,1.281 0.406,0.198 10 false ACC 1.698,1.49 2.104,1.688 0.406,0.198 10 false GND2 5.167,1.479 5.729,1.708 0.563,0.229 10 false GND 1.813,1.885 2.219,2.083 0.406,0.198 10 false LV1 5.177,1.885 5.583,2.083 0.406,0.198 10 false LV 2.979,2.875 4.792,3.115 1.813,0.24 10 false : LVDS Communication Line 4.813,1.083 5.094,1.292 0.281,0.208 10 false z13 4.823,1.49 5.094,1.708 0.271,0.219 10 false z13

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU POWER SOURCE)
a.

Disconnect the V5 navigation ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z13-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z13-1 (B+) - z13-2 (GND) Always 11 to 14 V
z13-3 (ACC) - z13-2 (GND) Engine switch on (ACC) 11 to 14 V




OK

2.REPLACE HARNESS AND CONNECTOR (LVDS COMMUNICATION LINE)

NG

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
2.REPLACE HARNESS AND CONNECTOR (LVDS COMMUNICATION LINE)
a.

Replace the harness and connector (LVDS communication line).



c.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.




OK

END (LVDS COMMUNICATION LINE IS DEFECTIVE)

NG

3.REPLACE NAVIGATION ECU
3.REPLACE NAVIGATION ECU
a.

Replace the navigation ECU with a known good one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL).



c.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.




OK

END (NAVIGATION ECU IS DEFECTIVE)

NG

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
a.

Disconnect the z12 radio and display receiver assembly connector.


b.

Disconnect the z13 navigation ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z12-4 (+B2) - z13-1 (B+) Always Below 1 Ω
z12-3 (ACC2) - z13-3 (ACC) Always Below 1 Ω
z12-8 (GND2) - z13-2 (GND) Always Below 1 Ω
z12-4 (+B2) - Body ground Always 10 kΩ or higher
z12-3 (ACC2) - Body ground Always 10 kΩ or higher
z12-8 (GND2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR