Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Multi-display) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261009 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display)  Reverse Signal Circuit  


DESCRIPTION

The clearance warning ECU receives a reverse shift position signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.

*1: for Automatic Transmission

*2: for Manual Transmission


WIRING DIAGRAM

E280619E08
5.417,0.978 5.833,1.165 0.416,0.187 10 RL 4.114,0.978 4.378,1.165 0.264,0.187 10 RL 4.408,0.866 4.672,1.053 0.264,0.187 10 1 5.207,0.866 5.470,1.053 0.264,0.187 10 8 3.259,0.866 3.523,1.053 0.264,0.187 10 2 3.427,0.978 3.691,1.165 0.264,0.187 10 RB 1.863,1.118 2.807,1.306 0.944,0.187 10 ECU-IG NO.1 3.175,1.483 4.112,1.670 0.937,0.187 10 C40 3.175,1.651 4.565,1.996 1.390,0.345 10 Park/Neutral Position Switch Assembly 5.193,1.609 6.130,1.796 0.937,0.187 10 I1*1, G154*2 5.193,1.777 6.708,2.122 1.515,0.345 10 Clearance Warning ECU 0.072,2.162 1.782,2.313 1.710,0.151 10 *1: for 4 Sensor Type 0.072,2.456 1.782,2.607 1.710,0.151 10 *2: for 8 Sensor Type 0.154,0.964 1.535,1.151 1.382,0.187 10 from IG1 NO.1 Relay 0.149,0.09 2.560,0.406 2.411,0.316 12 for Automatic Transmission:

E280619E09
5.417,0.978 5.833,1.165 0.416,0.187 10 RL 4.408,0.866 4.672,1.053 0.264,0.187 10 1 5.207,0.866 5.470,1.053 0.264,0.187 10 8 3.259,0.866 3.523,1.053 0.264,0.187 10 2 1.863,1.118 2.807,1.306 0.944,0.187 10 ECU-IG NO.1 3.175,1.483 4.112,1.670 0.937,0.187 10 C41 3.175,1.651 4.565,1.996 1.390,0.345 10 Back-up Light Switch Assembly 5.193,1.609 6.130,1.796 0.937,0.187 10 I1*1, G154*2 5.193,1.777 6.708,2.122 1.515,0.345 10 Clearance Warning ECU 0.1,2.134 1.810,2.285 1.710,0.151 10 *1: for 4 Sensor Type 0.1,2.428 1.810,2.579 1.710,0.151 10 *2: for 8 Sensor Type 0.154,0.964 1.535,1.151 1.382,0.187 10 from IG1 NO.1 Relay 0.051,0.048 2.462,0.364 2.411,0.316 12 for Manual Transmission:

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CLEARANCE WARNING ECU
a.
U169630E01
1.176,0.457 1.403,0.632 0.227,0.174 10 I1 1.515,0.457 1.743,0.632 0.227,0.174 10 *A 1.861,0.453 2.224,0.627 0.363,0.174 10 G154 2.385,0.453 2.612,0.627 0.227,0.174 10 *B 2.396,1.319 2.932,1.429 false 2.962,1.356 3.198,1.508 0.236,0.152 10 RL 0.041,0.014 0.271,0.225 0.230,0.211 10 *a

Disconnect the clearance warning ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 4 Sensor Type
Tester Connection Condition Specified Condition
I1-8 (RL) - Body ground Engine switch on (IG)
Shift lever in R
11 to 14 V
I1-8 (RL) - Body ground Engine switch on (IG)
Shift lever in any position except R
Below 1 V

for 8 Sensor Type
Tester Connection Condition Specified Condition
G154-8 (RL) - Body ground Engine switch on (IG)
Shift lever in R
11 to 14 V
G154-8 (RL) - Body ground Engine switch on (IG)
Shift lever in any position except R
Below 1 V


Text in Illustration
*A for 4 Sensor Type
*B for 8 Sensor Type
*a Front view of wire harness connector
(to Clearance Warning ECU)

Result
Result Proceed to
OK A
NG (for Automatic Transmission) B
NG (for Manual Transmission) C



A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

4.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

b.

Inspect the park/neutral position switch assembly.


Result
Result Proceed to
OK A
NG (for AC60F) B
NG (for A750F) C



A

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - CLEARANCE WARNING ECU AND BATTERY)

B

C

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - CLEARANCE WARNING ECU AND BATTERY)
a.

Disconnect the C40 park/neutral position switch assembly connector.


b.

Disconnect the I1*1 or G154*2 clearance warning ECU connector.

*1: for 4 Sensor Type

*2: for 8 Sensor Type



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C40-2 (RB) - Body ground Engine switch on (IG) 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 4 Sensor Type
Tester Connection Condition Specified Condition
I1-8 (RL) - C40-1 (RL) Always Below 1 Ω
I1-8 (RL) - Body ground Always 10 kΩ or higher

for 8 Sensor Type
Tester Connection Condition Specified Condition
G154-8 (RL) - C40-1 (RL) Always Below 1 Ω
G154-8 (RL) - Body ground Always 10 kΩ or higher



Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY

A

5.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - CLEARANCE WARNING ECU AND BATTERY)

B

C

D

5.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - CLEARANCE WARNING ECU AND BATTERY)
a.

Disconnect the C41 back-up light switch assembly connector.


b.

Disconnect the I1*1 or G154*2 clearance warning ECU connector.

*1: for 4 Sensor Type

*2: for 8 Sensor Type



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C41-2 - Body ground Engine switch on (IG) 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 4 Sensor Type
Tester Connection Condition Specified Condition
I1-8 (RL) - C41-1 Always Below 1 Ω
I1-8 (RL) - Body ground Always 10 kΩ or higher

for 8 Sensor Type
Tester Connection Condition Specified Condition
G154-8 (RL) - C41-1 Always Below 1 Ω
G154-8 (RL) - Body ground Always 10 kΩ or higher



Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR