Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › CLEARANCE WARNING ECU (for RHD) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261005 CLEARANCE WARNING ECU(for RHD) A

PARK ASSIST / MONITORING  CLEARANCE WARNING ECU(for RHD)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for 4 Sensor Type)

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 67910 3.REMOVE DOOR SCUFF PLATE ASSEMBLY RH (for 4 Sensor Type)

E200370E03
3.115,1.083 2.969,1.083 2.969,1.083 2.802,1.146 false 0.354,1.958 0.573,1.958 0.573,1.958 1.448,2.448 false 0.167,1.865 0.344,2.031 0.177,0.167 10 false *1 3.135,0.979 3.385,1.208 0.25,0.229 10 true *1

a.

Put protective tape around the door scuff plate assembly RH.


b.

Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate assembly RH.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 62111C 4.REMOVE COWL SIDE TRIM BOARD RH (for 4 Sensor Type)

E200371

a.

Remove the clip.


b.

Detach the clip and claw and remove the cowl side trim board RH.


Hide 55317A 5.REMOVE INSTRUMENT SIDE PANEL RH (for 4 Sensor Type)

E200372E01
1.146,1.188 1.299,1.355 0.154,0.167 10 *1 1.315,1.277 1.674,1.277 false

a.

Put protective tape around the instrument side panel RH.

Text in Illustration
*1 Protective Tape


b.

Using a moulding remover, detach the 5 clips, claw and 3 guides and remove the instrument side panel RH.


Hide 55480D 6.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for 4 Sensor Type)

E200373

a.

Detach the 4 clips.


b.

Disconnect each connector and remove the lower instrument panel finish panel assembly.


Hide 55476C 7.REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for 4 Sensor Type)

Hide 55606 8.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for 4 Sensor Type)

Hide 55045 9.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for 4 Sensor Type)

a.
E201134E01
2.166,0.55 2.364,0.697 0.198,0.147 10 *1 2.166,0.649 1.907,0.649 1.907,0.649 1.711,0.788 false

Using a screwdriver, detach the 2 claws and open the cover.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


b.
E200374

Remove the 2 bolts.


c.

Detach the 14 clips.


d.

Disconnect each connector and each cable and remove the lower instrument panel finish panel sub-assembly.


Hide 73900 10.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for 4 Sensor Type)

B362705

a.

Disconnect the connector.


b.

Remove the 4 bolts and lower No. 1 instrument panel airbag assembly.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.



Hide 82730A 11.REMOVE DRIVER SIDE JUNCTION BLOCK ASSEMBLY (for 4 Sensor Type)

Hide 89340A 12.REMOVE CLEARANCE WARNING ECU ASSEMBLY (for 4 Sensor Type)

E197679

a.

Disconnect the connector.


b.

Remove the bolt and clearance warning ECU assembly.


Hide 67920 13.REMOVE DOOR SCUFF PLATE ASSEMBLY LH (for 8 Sensor Type)

B238732E06
0.417,1.229 0.49,1.229 false 0.49,1.229 0.635,1.188 false 2.021,2.396 2.938,2.042 false 2.938,2.042 3.083,2.042 false 0.24,1.135 0.49,1.323 0.25,0.188 10 true *1 3.063,1.948 3.281,2.167 0.219,0.219 10 true *1

a.

Put protective tape around the door scuff plate assembly LH.


b.

Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate assembly LH.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 62112 14.REMOVE COWL SIDE TRIM BOARD LH (for 8 Sensor Type)

B238734

a.

Remove the clip.


b.

Detach the clip and claw and remove the cowl side trim board LH.


Hide 55318C 15.REMOVE INSTRUMENT SIDE PANEL LH (for 8 Sensor Type)

B238213E01
1.734,1.38 2.502,1.096 2.502,1.096 2.849,1.096 false 2.892,0.989 3.138,1.200 0.246,0.211 10 *1

a.

Put protective tape around the instrument side panel LH.

Text in Illustration
*1 Protective Tape


b.

Using a moulding remover, detach the 5 clips, claw and 3 guides and remove the instrument side panel LH.


Hide 55461A 16.REMOVE INSTRUMENT PANEL ORNAMENT (for 8 Sensor Type)

B238218E01
1.859,0.731 2.015,0.912 0.156,0.181 10 *1 1.663,0.993 1.755,0.832 1.755,0.832 1.852,0.832 false

a.

Put protective tape around the instrument panel ornament.

Text in Illustration
*1 Protective Tape


b.

Using a moulding remover, detach the 5 clips and remove the instrument panel ornament.


Hide 55607 17.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for 8 Sensor Type)

Hide 55550 18.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (for 8 Sensor Type)

B238220E02
0.438,2.667 0.646,2.844 0.208,0.177 10 true *1 2.792,2.667 2.99,2.917 0.198,0.25 10 true *1 2.385,1.24 2.635,1.521 0.25,0.281 10 true *2 1.167,1.375 1.323,1.531 0.156,0.156 10 false *2

a.

Remove the 2 bolts and 2 screws.

Text in Illustration
*1 Bolt
*2 Screw


b.

Detach the 5 clips and claw.


c.

Disconnect each connector and remove the glove compartment door assembly.


Hide 89340A 19.REMOVE CLEARANCE WARNING ECU ASSEMBLY (for 8 Sensor Type)

B359129

a.

Disconnect the connector.


b.

Remove the 2 nuts and clearance warning ECU assembly.