Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Multi-display) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261009 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display) C

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display)  C1AED  Rear Sensor Communication Malfunction  


DESCRIPTION

This DTC is stored when there is an open or short circuit in the communication line between the rear sensors and ECU, or when there is a malfunction in a rear sensor.

DTC Code DTC Detection Condition Trouble Area
C1AED An open or short circuit in the communication line between the rear sensors and ECU or a malfunction in a rear sensor during initialization mode after the engine switch is turned on (IG).
·

Rear ultrasonic sensor circuit

·

Clearance warning ECU



WIRING DIAGRAM

E283768E24
5.615,2.104 5.896,2.292 0.281,0.188 10 false I1*1 5.615,2.281 6.844,2.656 1.229,0.375 10 false Clearance Warning ECU 5.75,1.031 6.365,1.229 0.615,0.198 10 false SOR 5.75,1.302 6.365,1.5 0.615,0.198 10 false BOR 3.969,1.604 4.177,1.813 0.208,0.208 10 false EI 5.479,0.927 5.698,1.115 0.219,0.188 10 false 24 5.469,1.229 5.688,1.417 0.219,0.188 10 false 7 5.469,1.5 5.688,1.688 0.219,0.188 10 false 18 3.042,1.938 3.656,2.135 0.615,0.198 10 false V5 3.042,2.135 4.625,2.573 1.583,0.438 10 false NO. 1 Ultrasonic Sensor (Rear Corner Sensor LH) 0.698,1.948 1.313,2.146 0.615,0.198 10 false V4 0.708,2.135 2.292,2.625 1.583,0.49 10 false NO. 1 Ultrasonic Sensor (Rear Center Sensor LH) 0.719,3.969 1.333,4.167 0.615,0.198 10 false U4 0.719,4.156 2.302,4.729 1.583,0.573 10 false NO. 1 Ultrasonic Sensor (Rear Center Sensor RH) 3.021,3.979 3.635,4.177 0.615,0.198 10 false U5 3.021,4.156 4.594,4.719 1.573,0.563 10 false NO. 1 Ultrasonic Sensor (Rear Corner Sensor RH) 5.75,1.573 6,1.792 0.25,0.219 10 false E2 3.969,1.323 4.177,1.531 0.208,0.208 10 false BI 3.969,1.042 4.177,1.25 0.208,0.208 10 false SI 3.177,1.052 3.479,1.281 0.302,0.229 10 false SO 3.177,1.323 3.448,1.521 0.271,0.198 10 false BO 3.177,1.594 3.458,1.813 0.281,0.219 10 false EO 0.958,1.021 1.25,1.229 0.292,0.208 10 false SO 0.969,1.302 1.229,1.531 0.26,0.229 10 false BO 0.969,1.583 1.271,1.802 0.302,0.219 10 false EO 1.781,1.01 1.99,1.219 0.208,0.208 10 false SI 1.771,1.292 1.979,1.5 0.208,0.208 10 false BI 1.771,1.583 1.979,1.792 0.208,0.208 10 false EI 0.969,3.031 1.177,3.24 0.208,0.208 10 false SI 0.969,3.323 1.177,3.531 0.208,0.208 10 false BI 0.969,3.615 1.177,3.823 0.208,0.208 10 false EI 1.708,3.052 1.979,3.24 0.271,0.188 10 false SO 1.708,3.323 1.969,3.552 0.26,0.229 10 false BO 1.708,3.604 2.01,3.823 0.302,0.219 10 false EO 3.208,3.042 3.417,3.25 0.208,0.208 10 false SI 3.219,3.313 3.427,3.521 0.208,0.208 10 false BI 3.219,3.604 3.427,3.813 0.208,0.208 10 false EI 4.26,0.948 4.479,1.135 0.219,0.188 10 false 3 4.26,1.229 4.479,1.417 0.219,0.188 10 false 1 4.271,1.5 4.49,1.688 0.219,0.188 10 false 5 2.031,0.938 2.25,1.125 0.219,0.188 10 false 3 2.031,1.24 2.25,1.427 0.219,0.188 10 false 1 2.042,1.5 2.26,1.688 0.219,0.188 10 false 5 0.771,2.958 0.99,3.146 0.219,0.188 10 false 3 0.76,3.25 0.979,3.438 0.219,0.188 10 false 1 0.771,3.542 0.99,3.729 0.219,0.188 10 false 5 3,2.969 3.219,3.156 0.219,0.188 10 false 3 3,3.26 3.219,3.448 0.219,0.188 10 false 1 3.01,3.531 3.229,3.719 0.219,0.188 10 false 5 2.958,0.948 3.177,1.135 0.219,0.188 10 false 4 2.958,1.219 3.177,1.406 0.219,0.188 10 false 2 2.958,1.51 3.177,1.698 0.219,0.188 10 false 6 0.781,0.938 1,1.125 0.219,0.188 10 false 4 0.771,1.219 0.99,1.406 0.219,0.188 10 false 2 0.771,1.49 0.99,1.677 0.219,0.188 10 false 6 2.042,2.938 2.26,3.125 0.219,0.188 10 false 4 2.042,3.25 2.26,3.438 0.219,0.188 10 false 2 2.042,3.531 2.26,3.719 0.219,0.188 10 false 6 5.917,2.104 6.427,2.271 0.51,0.167 10 false G154*2 0.135,5.021 1.646,5.229 1.51,0.208 10 false *1: for 4 Sensor Type 0.135,5.354 1.646,5.563 1.51,0.208 10 false *2: for 8 Sensor Type

PROCEDURE

1.CHECK FOR DTC (C1AED)

A

B

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - REAR CORNER SENSOR LH)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - REAR CORNER SENSOR LH)
a.

Disconnect the I1*1 or G154*2 clearance warning ECU connector.

*1: for 4 Sensor Type

*2: for 8 Sensor Type



b.

Disconnect the V5 No. 1 ultrasonic sensor (rear corner sensor LH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 4 Sensor Type
Tester Connection Condition Specified Condition
I1-7 (BOR) - V5-1 (BI) Always Below 1 Ω
I1-24 (SOR) - V5-3 (SI) Always Below 1 Ω
I1-18 (E2) - V5-5 (EI) Always Below 1 Ω
I1-7 (BOR) - Body ground Always 10 kΩ or higher
I1-24 (SOR) - Body ground Always 10 kΩ or higher
I1-18 (E2) - Body ground Always 10 kΩ or higher

for 8 Sensor Type
Tester Connection Condition Specified Condition
G154-7 (BOR) - V5-1 (BI) Always Below 1 Ω
G154-24 (SOR) - V5-3 (SI) Always Below 1 Ω
G154-18 (E2) - V5-5 (EI) Always Below 1 Ω
G154-7 (BOR) - Body ground Always 10 kΩ or higher
G154-24 (SOR) - Body ground Always 10 kΩ or higher
G154-18 (E2) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (REAR CORNER SENSOR LH - REAR CENTER SENSOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (REAR CORNER SENSOR LH - REAR CENTER SENSOR LH)
a.

Disconnect the V5 No. 1 ultrasonic sensor (rear corner sensor LH) connector.


b.

Disconnect the V4 No. 1 ultrasonic sensor (rear center sensor LH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V5-2 (BO) - V4-1 (BI) Always Below 1 Ω
V5-4 (SO) - V4-3 (SI) Always Below 1 Ω
V5-6 (EO) - V4-5 (EI) Always Below 1 Ω
V5-2 (BO) - Body ground Always 10 kΩ or higher
V5-4 (SO) - Body ground Always 10 kΩ or higher
V5-6 (EO) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (REAR CENTER SENSOR LH - REAR CENTER SENSOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR CENTER SENSOR LH - REAR CENTER SENSOR RH)
a.

Disconnect the V4 No. 1 ultrasonic sensor (rear center sensor LH) connector.


b.

Disconnect the U4 No. 1 ultrasonic sensor (rear center sensor RH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V4-2 (BO) - U4-1 (BI) Always Below 1 Ω
V4-4 (SO) - U4-3 (SI) Always Below 1 Ω
V4-6 (EO) - U4-5 (EI) Always Below 1 Ω
V4-2 (BO) - Body ground Always 10 kΩ or higher
V4-4 (SO) - Body ground Always 10 kΩ or higher
V4-6 (EO) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (REAR CENTER SENSOR RH - REAR CORNER SENSOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (REAR CENTER SENSOR RH - REAR CORNER SENSOR RH)
a.

Disconnect the U4 No. 1 ultrasonic sensor (rear center sensor RH) connector.


b.

Disconnect the U5 No. 1 ultrasonic sensor (rear corner sensor RH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U4-2 (BO) - U5-1 (BI) Always Below 1 Ω
U4-4 (SO) - U5-3 (SI) Always Below 1 Ω
U4-6 (EO) - U5-5 (EI) Always Below 1 Ω
U4-2 (BO) - Body ground Always 10 kΩ or higher
U4-4 (SO) - Body ground Always 10 kΩ or higher
U4-6 (EO) - Body ground Always 10 kΩ or higher




OK

6.INSPECT NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR LH)
a.

Remove the No. 1 ultrasonic sensor (rear corner sensor LH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL).


b.

Inspect the No. 1 ultrasonic sensor (rear corner sensor LH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>INSPECTION).



OK

7.INSPECT NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR LH)

NG

REPLACE NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR LH)

7.INSPECT NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR LH)
a.

Remove the No. 1 ultrasonic sensor (rear center sensor LH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL).


b.

Inspect the No. 1 ultrasonic sensor (rear center sensor LH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>INSPECTION).



OK

8.INSPECT NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)

NG

REPLACE NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR LH)

8.INSPECT NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)
a.

Remove the No. 1 ultrasonic sensor (rear center sensor RH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL).


b.

Inspect the No. 1 ultrasonic sensor (rear center sensor RH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>INSPECTION).



OK

9.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR RH)

NG

REPLACE NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)

9.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR RH)
a.

Replace the No. 1 ultrasonic sensor (rear corner sensor RH) with a normally functioning sensor (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL).

HINT:

All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.




NEXT

10.CHECK FOR DTC (C1AED)
10.CHECK FOR DTC (C1AED)

A

END (NO. 1 ULTRASONIC SENSOR [REAR CORNER SENSOR RH] WAS DEFECTIVE)

B

11.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR LH)
11.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR LH)
a.

Replace the No. 1 ultrasonic sensor (rear center sensor LH) with a normally functioning sensor (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL).

HINT:

All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.




NEXT

12.CHECK FOR DTC (C1AED)
12.CHECK FOR DTC (C1AED)

A

END (NO. 1 ULTRASONIC SENSOR [REAR CENTER SENSOR LH] WAS DEFECTIVE)

B

13.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)
13.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)
a.

Replace the No. 1 ultrasonic sensor (rear center sensor RH) with a normally functioning sensor (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL).

HINT:

All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.




NEXT

14.CHECK FOR DTC (C1AED)
14.CHECK FOR DTC (C1AED)

A

END (NO. 1 ULTRASONIC SENSOR [REAR CENTER SENSOR RH] WAS DEFECTIVE)

B

15.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR LH)
15.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR LH)
a.

Replace the No. 1 ultrasonic sensor (rear corner sensor LH) with a normally functioning sensor (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL).

HINT:

All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.




NEXT

16.CHECK FOR DTC (C1AED)
16.CHECK FOR DTC (C1AED)

A

END (NO. 1 ULTRASONIC SENSOR [REAR CORNER SENSOR LH] WAS DEFECTIVE)

B

C