Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2015.06–2020.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261011 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the blind spot monitor sensor.

WIRING DIAGRAM

E244551E54
3.604,0.698 3.917,0.875 0.313,0.177 10 false BLB 3.427,0.583 3.542,0.76 0.115,0.177 10 false 5 3.604,3.281 3.917,3.458 0.313,0.177 10 false BRB 3.417,3.188 3.531,3.365 0.115,0.177 10 false 5 3.604,4.094 4.042,4.271 0.438,0.177 10 false BRGD 3.344,3.99 3.521,4.167 0.177,0.177 10 false 10 3.354,1.365 3.531,1.542 0.177,0.177 10 false 10 3.604,1.49 4.031,1.646 0.427,0.156 10 false BLGD 1.938,0.885 2.281,1.104 0.344,0.219 10 false IG1 0.156,0.698 1.052,1.177 0.896,0.479 10 false from IG NO.1 Relay 6.313,0.854 7.042,1.625 0.729,0.771 10 false to CAN 3.469,4.542 3.833,4.75 0.365,0.208 10 false R43 3.458,4.76 4.635,5.156 1.177,0.396 10 false Blind Spot Monitor Sensor RH 3.396,2.219 4.625,2.625 1.229,0.406 10 false Blind Spot Monitor Sensor LH 0.854,5.313 2.854,5.469 2,0.156 10 false : CAN Communication Line 3.396,1.99 3.792,2.208 0.396,0.219 10 false R42

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH, BLIND SPOT MONITOR SENSOR RH - BATTERY AND BODY GROUND)
a.
U149473E04
1.948,1.26 2.396,0.844 2.396,0.844 2.615,0.844 true 1.969,1.51 2.396,2.031 2.396,2.031 2.615,2.031 true 1.948,3.552 2.396,3.135 2.396,3.135 2.615,3.135 true 1.969,3.823 2.396,4.344 2.396,4.344 2.615,4.344 true 0.083,0.021 0.448,0.271 0.365,0.25 10 false *a 1.573,0.406 1.938,0.583 0.365,0.177 10 false R42 2.667,0.76 3.031,0.938 0.365,0.177 10 false BLB 1.563,2.677 1.927,2.844 0.365,0.167 10 false R43 2.667,1.948 3.115,2.125 0.448,0.177 10 false BLGD 0.083,2.323 0.448,2.573 0.365,0.25 10 false *b 2.667,3.063 3.031,3.24 0.365,0.177 10 false BRB 2.667,4.271 3.115,4.448 0.448,0.177 10 false BRGD

Disconnect the blind spot monitor sensor LH connector.


b.

Disconnect the blind spot monitor sensor RH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R42-5 (BLB) - Body ground Engine switch on (IG) 11 to 14 V
R42-5 (BLB) - Body ground Engine switch off Below 1 V
R43-5 (BRB) - Body ground Engine switch on (IG) 11 to 14 V
R43-5 (BRB) - Body ground Engine switch off Below 1 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R42-10 (BLGD) - Body ground Always Below 1 Ω
R43-10 (BRGD) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
*b Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR