Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261011 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  OPERATION CHECK  


BLIND SPOT MONITOR BEAM AXIS INSPECTION


a.

Procedure to enter Test Mode

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the blind spot monitor main switch assembly (multi-function switch) on.


iv.

Turn the GTS on.


v.

Switch the blind spot monitor sensor to Test Mode using the GTS. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master beam axis inspection or BSM Slave beam axis inspection.


vi.

Finish Test Mode.




BLIND SPOT MONITOR BEAM AXIS CONFIRMATION


a.

When performing the blind spot monitor beam axis confirmation, move the vehicle to a place where the space shown in the illustration can be secured.

U131939E01
0.059,0 0.742,0.184 0.682,0.184 12 LH Side: 3.889,0 4.782,0.184 0.894,0.184 12 RH Side: 0.986,3.974 1.918,4.172 0.931,0.198 10 6 m (19.69 ft.) 2.121,3.995 2.976,4.193 0.855,0.198 10 3 m (9.85 ft.) 4.279,3.995 5.134,4.193 0.855,0.198 10 3 m (9.85 ft.) 0.397,0.662 1.302,0.859 0.905,0.198 10 8 m (26.25 ft.) 5.819,0.662 6.724,0.859 0.905,0.198 10 8 m (26.25 ft.) 3.137,1.795 4.001,1.979 0.864,0.184 10 Rear Bumper 1.435,0.319 2.653,0.510 1.218,0.191 10 Left side of vehicle 4.55,0.319 5.865,0.510 1.315,0.191 10 Right side of vehicle 1.295,4.345 2.376,4.543 1.082,0.198 10 : Inspection Area 5.33,4.009 6.261,4.207 0.931,0.198 10 6 m (19.69 ft.) 0.459,1.021 1.277,1.225 0.818,0.205 10 2 m (6.57 ft.) 5.855,1.023 6.673,1.228 0.818,0.205 10 2 m (6.57 ft.)

NOTICE:
·

Perform this inspection on level ground.

·

Make sure that there are no metal objects around the vehicle or on the ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.

·

Do not place an object other than the reflector (such as a large metallic object) in or allow people to enter the inspection area (W 9 m (29.53 ft.) x L 10 m (32.81 ft.) x H 4 m (13.13 ft.)) shown in the illustration.

·

Check that DTC C1ABB and DTC C1ABC are not output.




b.

Place the reflector.

i.

w/o Tire Carrier:

Hang a weight with a pointed tip from the center of the symbol emblem, and mark the front center point of the vehicle (point A) on the ground.

E407536C01
2.906,2.344 3.365,2.208 false 2.896,2.458 3.375,2.552 false 5.073,1.073 5.667,0.854 true 5.063,2.271 5.604,2.458 false 5.688,2.385 6,2.583 0.313,0.198 10 false *a 5.198,2 5.51,2.198 0.313,0.198 10 false *d 4.771,1.99 5.083,2.188 0.313,0.198 10 false *d 5.771,0.74 6.083,0.938 0.313,0.198 10 false *c 3.427,2.094 3.74,2.292 0.313,0.198 10 false *b 3.448,2.479 3.76,2.677 0.313,0.198 10 false A
*a String *b Weight
*c Center *d Bilateral Symmetry


HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.



ii.

w/ Tire Carrier:

Hang a weight with a pointed tip from the center of the rear bumper cover, and mark the front center point of the vehicle (point A) on the ground.

E407537C01
2.906,2.313 3.281,2.25 false 2.917,2.448 3.25,2.594 false 5.396,2.031 5.792,2.229 false 5.896,2.167 6.208,2.365 0.313,0.198 10 false *a 5.76,1.896 6.073,2.094 0.313,0.198 10 false *c 4.906,1.896 5.219,2.094 0.313,0.198 10 false *c 3.354,2.146 3.667,2.344 0.313,0.198 10 false *b 3.354,2.542 3.667,2.74 0.313,0.198 10 false A
*a String *b Weight
*c Bilateral Symmetry - -


HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.



iii.

Hang a weight with a pointed tip from the center of the radiator grille emblem, and mark the front center point of the vehicle (point B) on the ground.

E407538C01
2.031,1.01 2.656,0.833 true 2.021,2.167 2.448,2.323 false 3.646,2.125 4.073,2.281 false 3.677,2.51 4.083,2.385 false 2.719,0.74 3.031,0.938 0.313,0.198 10 false *c 2.146,1.927 2.458,2.125 0.313,0.198 10 false *d 1.729,1.927 2.042,2.125 0.313,0.198 10 false *d 2.531,2.271 2.844,2.469 0.313,0.198 10 false *a 3.448,2 3.76,2.198 0.313,0.198 10 false *b 3.51,2.438 3.823,2.635 0.313,0.198 10 false B
*a String *b Weight
*c Center *d Bilateral Symmetry


HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.



iv.
E238824E01
1.439,1.257 1.206,1.541 false 3.022,1.262 3.177,1.627 false 0.633,1.258 1.092,0.453 false 1.092,0.453 1.292,0.453 false 1.321,0.355 2.528,0.516 1.207,0.161 10 Vehicle center line 1.1,1.532 1.261,1.693 0.161,0.161 10 A 3.186,1.624 3.347,1.785 0.161,0.161 10 B

Draw a vehicle center line so that it passes through mark (A) and (B) (front and rear center points).


v.
E238823E49
0.292,1.688 0.365,1.281 false 1.292,1.688 1.438,1.281 false 3.188,1.688 3.021,1.281 false 1.229,1.729 1.51,1.917 0.281,0.188 10 false A 3.167,1.729 3.365,1.969 0.198,0.24 10 false B 0.25,1.719 0.479,1.906 0.229,0.188 10 false C 0.323,0.146 2.542,0.354 2.219,0.208 10 false 555 to 575 mm (1.82 to 1.89 ft.)

Mark the position on the center line 555 to 575 mm (1.82 to 1.89 ft.) behind the rear bumper. (Mark (C))


vi.
E238825E22
1.719,3.771 2.094,3.208 2.094,3.208 2.302,3.208 false 0.135,3.375 1.302,3.583 1.167,0.208 10 false 300 mm (11.8 in.) 2.396,3.115 2.583,3.313 0.188,0.198 10 false C 0.26,0 1.156,0.156 0.896,0.156 10 false Vehicle front 0.135,3.833 1.302,4.042 1.167,0.208 10 false 300 mm (11.8 in.)

Prepare 2 pieces of string of 600 mm (1.97 ft.) in length and secure the end of each string at a point 300 mm (11.8 in.) from mark (C) as shown in the illustration.


vii.

Pull the end of each string and mark the position where each string meets on both the left and right side (marks (D) and (E)).

E238826E16
1.333,2.042 1.25,1.854 1.25,1.854 1.115,1.854 false 1.552,2.188 1.292,2.365 1.292,2.365 1.167,2.365 false 2.25,1.823 2.125,1.823 2.125,1.823 2,2.052 false 1.677,1.854 1.563,1.448 1.563,1.448 1.396,1.448 false 4.125,2.063 3.865,2.25 3.865,2.25 3.74,2.25 false 5.667,2.333 5.292,2.333 5.292,2.333 5.188,2.229 false 5.708,1.833 5.542,1.833 5.542,1.833 5.458,2.063 false 5.583,1.188 5.417,1.188 5.417,1.188 5.094,1.844 false 4.781,2.052 4.667,1.646 4.667,1.646 4.5,1.646 false 5.229,0.125 5.063,0.125 5.063,0.125 4.802,0.313 false 2.438,0.115 2.271,0.115 2.271,0.115 2.01,0.302 false 5.771,1.74 6.854,1.938 1.083,0.198 12 false E 1,1.344 1.448,1.542 0.448,0.198 10 false String 0.938,1.76 1.156,1.979 0.219,0.219 12 false D 2.302,1.719 2.5,1.917 0.198,0.198 12 false C 3.594,2.156 3.74,2.354 0.146,0.198 12 false D 4.344,1.563 4.542,1.76 0.198,0.198 12 false C 0.052,0 1.385,0.313 1.333,0.313 12 false Vehicle rear: 0.729,2.271 1.177,2.469 0.448,0.198 10 false String 5.656,1.104 6.104,1.302 0.448,0.198 10 false String 5.729,2.26 6.177,2.458 0.448,0.198 10 false String 2.49,0.031 3.677,0.344 1.188,0.313 10 false Vehicle center line 5.302,0.031 6.531,0.344 1.229,0.313 10 false Vehicle center line


viii.
E238827E20
1.688,0.5 1.979,0.177 1.979,0.177 2.104,0.177 false 2.333,3.906 2.625,3.583 2.625,3.583 2.75,3.583 false 0.74,4.146 0.885,4.146 0.885,4.146 1.063,3.938 false 2.313,4.302 2.156,4.302 2.156,4.302 1.927,3.938 false 2.781,3.5 2.958,3.698 0.177,0.198 12 false E 0.563,4.052 0.708,4.25 0.146,0.198 12 false D 0.292,0.115 1.135,0.313 0.844,0.198 10 false Vehicle front 2.208,0.115 3.104,0.427 0.896,0.313 10 false Vehicle center line 2.365,4.229 2.885,4.49 0.521,0.26 10 false Line P

Draw a line (P) so that it passes through mark (D) and (E) and is perpendicular to the vehicle center line.


ix.

Set the reflector at the position (Z) shown in the illustration below.

SST
09870-60000  (09870-60010)
09870-60040  

E233794E39
0.688,3.229 1.094,2.917 false 6.24,3.104 5.906,2.917 false 2.688,2.208 2.917,1.781 false 2.917,1.781 3.052,1.781 false 4.385,2.208 4.135,1.792 false 4.135,1.792 3.979,1.792 false 5.313,2.563 5.552,1.781 false 5.552,1.781 5.698,1.781 false 2.01,2.385 1.74,1.854 false 1.74,1.854 1.573,1.854 false 2.563,2.865 2.719,3.156 false 2.719,3.156 2.771,3.156 false 4.542,2.854 4.365,3.146 false 4.365,3.146 4.302,3.146 false 1.188,2.833 1.063,2.323 false 1.063,2.323 0.99,2.323 false 5.854,2.813 5.969,2.323 false 5.969,2.323 6.031,2.323 false 0.167,0.063 0.875,0.333 0.708,0.271 12 false LH Side: 3.24,0.042 3.958,0.281 0.719,0.24 12 false RH Side: 4.104,0.156 5.313,0.323 1.208,0.167 10 false Vehicle center line 0.875,2.24 1.031,2.427 0.156,0.188 10 false Z 6.052,2.24 6.177,2.427 0.125,0.188 10 false Z 0.323,3.26 0.917,3.427 0.594,0.167 10 false Reflector 6.063,3.135 6.656,3.302 0.594,0.167 10 false Reflector 1.76,0.188 2.969,0.354 1.208,0.167 10 false Vehicle center line 3.094,1.667 3.969,1.833 0.875,0.167 10 false Rear bumper 2.979,2.323 4.104,2.531 1.125,0.208 10 false 555 to 575 mm 0.344,1.76 1.594,2.021 1.25,0.26 10 false 3258 mm (10.69 ft.) 2.792,3.052 3.281,3.219 0.49,0.167 10 false Line P 3.885,3.042 4.375,3.208 0.49,0.167 10 false Line P 4.708,3.167 5.917,3.385 1.208,0.219 10 false 3198 to 3218 mm 5.781,1.708 7.031,2.031 1.25,0.323 10 false 3258 mm (10.69 ft.) 1.198,3.208 2.406,3.427 1.208,0.219 10 false 3198 to 3218 mm 2.958,2.521 4.083,2.729 1.125,0.208 10 false (1.82 to 1.89 ft.) 4.708,3.385 5.917,3.604 1.208,0.219 10 false (10.49 to 10.56 ft.) 1.188,3.417 2.396,3.635 1.208,0.219 10 false (10.49 to 10.56 ft.)

NOTICE:
·
E238830E45
0.115,1.313 0.656,1.49 0.542,0.177 10 false 867 mm 0.115,1.51 0.656,1.688 0.542,0.177 10 false (2.84 ft.)

Set the reflector so that its center is 867 mm (2.84 ft.) above the ground.

·
E238829E21
2.01,0.677 2.5,1.302 false 1.865,1.323 3.094,1.667 1.229,0.344 10 false Center of triangular pyramid

The center of triangular pyramid is the reference point for the setting position and angle.

·

Set the reflector as shown in the illustration so that its center of triangular pyramid faces the blind spot monitor sensor.

·

Perform the operation as precisely as possible.





c.

Perform the blind spot monitor beam axis display.

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the blind spot monitor main switch assembly (multi-function switch) on.


iv.

Turn the GTS on.


v.

Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master beam axis display or BSM Slave beam axis display.


vi.

Check the results displayed for the BSM beam axis display.

Allowable Range:
Item Blind Spot Monitor Sensor LH (Master) Blind Spot Monitor Sensor RH (Slave)
Angle -3.6 to +3.6° -3.6 to +3.6°
Distance 2.0 to 3.0 m
(6.57 to 9.85 ft.)
2.0 to 3.0 m
(6.57 to 9.85 ft.)


HINT:

If the results are outside the allowable range, try again as the reflector setting position may be incorrect or a metal object may exist near the detection area.



vii.

Perform the blind spot monitor beam axis adjustment using the GTS. Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master beam axis adjustment or BSM Slave beam axis adjustment.

HINT:

When values on the axis display are in the allowable range, performing this adjustment compensates the values to the normal value.





BLIND SPOT MONITOR INSTALLATION CONDITION INSPECTION


NOTICE:
·

Perform this inspection on level ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.



a.

b.

Attach a jig similar to the one shown in the illustration to the outward facing surface of the blind spot monitor sensor and check that the blind spot monitor sensor is perpendicular to the floor surface or within the allowable range.

E233717E03
5.917,3.958 5.917,3.417 false 5.917,3.417 6.063,3.417 false 1.948,3.583 1.948,2.448 false 2.302,2.115 2.979,3.5 false 5.052,1.208 5.583,0.615 false 5.583,0.615 5.729,0.615 false 4.615,3.25 4.875,3.25 false 2.979,3.5 3.094,3.5 false 6.083,3.344 6.917,3.531 0.833,0.188 10 Floor surface 1.188,3.583 2.906,3.75 1.719,0.167 10 Blind Spot Monitor Sensor 3.125,3.438 4.813,3.646 1.688,0.208 10 Outward facing surface 0.156,0.063 2.281,0.448 2.125,0.385 12 Rear view of vehicle (RH): 5.76,0.552 6.208,0.792 0.448,0.24 10 Jig 4.906,3.188 5.479,3.427 0.573,0.24 10 Weight

E233716E01
1.653,0.769 3.071,1.296 1.418,0.527 10 Hold this side against the blind spot monitor sensor RH. 3.271,1.552 3.550,1.761 0.279,0.209 10 Top 5.338,3.141 5.910,3.325 0.573,0.184 10 100 mm 2.76,4.08 2.944,4.264 0.184,0.184 10 A 3.979,4.08 4.163,4.264 0.184,0.184 10 B 1.356,2.821 2.843,3.168 1.487,0.347 10 Position where string is to be secured 1.046,6.181 2.146,6.339 1.100,0.157 10 : Allowable range 0.223,0.184 0.834,0.419 0.611,0.236 12 Jig: 1.548,4.984 1.732,5.167 0.184,0.184 10 + 5.163,4.984 5.346,5.167 0.184,0.184 10 - 5.352,3.295 5.994,3.479 0.642,0.184 10 (3.34 in.) 4.105,0.769 5.522,1.296 1.418,0.527 10 Hold this side against the blind spot monitor sensor LH.

Standard
A B
Blind spot monitor sensor RH 8 mm
(0.315 in.)
-8 mm
(-0.315 in.)
Blind spot monitor sensor LH 8 mm
(0.315 in.)
-8 mm
(-0.315 in.)


c.
E224437E31
1.229,3.604 1.469,4.01 false 2.521,0.635 2.917,1.167 false 0.781,3.573 0.729,3.854 false 0.552,3.833 0.271,3.906 false 0.271,3.906 0.271,4.281 false 1.427,1.979 1.594,1.646 false 1.594,1.646 1.667,1.646 false 1.469,4.01 1.563,4.01 false 0.094,0 1.448,0.208 1.354,0.208 12 false Vehicle rear (LH): 1.094,0.49 2.26,0.802 1.167,0.313 10 false Vehicle center line 1.594,3.927 2.219,4.094 0.625,0.167 10 false Stud bolt 1.448,0.896 2.24,1.063 0.792,0.167 10 false Vehicle front 0.688,3.823 0.813,3.99 0.125,0.167 10 false y 1.938,3.656 2.698,3.823 0.76,0.167 10 false Vehicle rear 0.052,4.26 2.427,4.427 2.375,0.167 10 false Line parallel to the vehicle center line 1.813,2.385 2.344,2.573 0.531,0.188 10 false 104 mm 1.698,1.573 2.719,1.896 1.021,0.323 10 false Stud bolt center line 1.823,2.594 2.51,2.781 0.688,0.188 10 false (4.09 in.)

Using the sensor installation stud bolt center lines as a reference, check that the stud bolts are as shown in the illustration.

Standard:
Dimension Specified Value
y 29 to 42 mm
(1.15 to 1.65 in.)