Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261015 PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System) C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the parking assist ECU receives a signal via CAN communication from the spiral cable sub-assembly that indicates a power supply system problem.

DTC Code DTC Detection Condition Trouble Area
C1625 Open or short in steering angle sensor +B
·

Harness or connector

·

Spiral cable sub-assembly



WIRING DIAGRAM

E224380E86
1.125,3.219 2.875,3.396 1.75,0.177 10 false : CAN Communication Line 3.229,0.604 3.583,0.781 0.354,0.177 10 false BAT 3.229,1.708 3.563,1.885 0.333,0.177 10 false ESS 5.375,2.198 6.646,2.427 1.271,0.229 10 false Parking Assist ECU 2.031,1.344 3.042,1.521 1.01,0.177 10 false ECU-IG NO.1 2.271,0.813 2.823,1 0.552,0.188 10 false ECU-B 0.385,1.188 1.76,1.417 1.375,0.229 10 false from IG1 NO.1 Relay 0.938,0.635 1.865,0.813 0.927,0.177 10 false from Battery 2.969,2.344 4.51,2.75 1.542,0.406 10 false Spiral with Sensor Cable Sub-assembly 3.031,0.51 3.156,0.688 0.125,0.177 10 false 6 3.031,1.052 3.156,1.229 0.125,0.177 10 false 5 3.031,1.604 3.25,1.792 0.219,0.188 10 false 2 3.229,1.156 3.531,1.333 0.302,0.177 10 false IG 2.979,2.177 3.323,2.354 0.344,0.177 10 false G33

CAUTION / NOTICE / HINT

NOTICE:
·

Since the parking assist monitor system has functions that use CAN communication system, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.

·

When "System initializing" is displayed on the parking assist ECU after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY AND BODY GROUND)
a.
U149474E01
1.548,0.28 1.861,0.461 0.312,0.181 10 G33 0.051,0.009 0.221,0.176 0.170,0.167 10 *a 1.478,1.869 1.658,2.036 0.180,0.167 10 IG 2.077,1.504 1.904,1.944 1.904,1.944 1.705,1.944 false 2.294,1.504 2.481,1.883 2.481,1.883 2.679,1.883 false 1.329,1.533 1.076,1.899 1.076,1.899 0.877,1.899 false 0.519,1.823 0.824,1.991 0.305,0.167 10 ESS 2.69,1.808 2.995,1.976 0.305,0.167 10 BAT

Disconnect the G33 spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-2 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G33-5 (IG) - G33-2 (ESS) Engine switch on (IG) 11 to 14 V
G33-6 (BAT) - G33-2 (ESS) Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR