Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261030 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1249  Double Locking ECU Communication Stop  


DESCRIPTION

DTC B1249 is stored when communication between the double lock door control relay assembly and main body ECU (multiplex network body ECU) stops for more than 10 seconds.

DTC Code DTC Detection Condition Trouble Area
B1249 Communication between the double lock door control relay assembly and main body ECU (multiplex network body ECU) stops for more than 10 seconds.
·

Double lock door control relay assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

C212385E02
3.005,0.865 3.816,1.033 0.811,0.168 10 from Battery 4.537,1.015 5.259,1.210 0.722,0.195 10 SECURITY 4.541,1.503 5.238,1.693 0.697,0.190 10 D/L NO. 2 0.741,0.819 1.070,0.977 0.328,0.158 10 A 0.741,0.999 2.409,1.379 1.668,0.379 10 Main Body ECU (Multiplex Network Body ECU) 5.418,0.872 5.882,1.044 0.464,0.172 10 CPUB 5.418,0.486 5.882,0.658 0.464,0.172 10 MPX1 5.418,1.814 5.817,1.986 0.399,0.172 10 GND 5.418,1.372 5.649,1.544 0.231,0.172 10 +B 1.564,0.451 1.885,0.607 0.321,0.156 10 LIN2 1.981,0.374 2.163,0.530 0.182,0.156 10 16 4.494,2.305 7.151,2.469 2.657,0.164 10 Double Lock Door Control Relay Assembly 5.223,0.801 5.333,0.973 0.110,0.172 10 7 5.228,0.374 5.341,0.546 0.113,0.172 10 9 5.138,1.742 5.324,1.914 0.186,0.172 10 14 5.223,1.299 5.336,1.471 0.113,0.172 10 1 4.493,2.154 5.022,2.343 0.529,0.189 10 G49

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.



HINT:

When communication between the double lock door control relay and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1249 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOUBLE LOCK DOOR CONTROL RELAY)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOUBLE LOCK DOOR CONTROL RELAY)
a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Disconnect the G49 double lock door control relay assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - G49-9 (MPX1) Always Below 1 Ω
A-16 (LIN2) or G49-9 (MPX1) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY - BATTERY AND BODY GROUND)
a.
U170597E02
1,1.156 0.729,0.823 0.729,0.823 0.604,0.823 true 1.031,1.49 0.854,1.76 0.854,1.76 0.719,1.76 true 2.385,1.479 2.51,1.76 2.51,1.76 2.688,1.76 true 0.073,0.042 0.313,0.229 0.24,0.188 10 false *a 0.313,1.281 0.625,1.469 0.313,0.188 10 false G49 0.365,0.74 0.573,0.927 0.208,0.188 10 false +B 0.229,1.667 0.646,1.854 0.417,0.188 10 false CPUB 2.708,1.667 3.052,1.854 0.344,0.188 10 false GND

Disconnect the G49 double lock door control relay assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G49-14 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G49-1 (+B) - Body ground Always 11 to 14 V
G49-7 (CPUB) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Double Lock Door Control Relay Assembly)


OK

5.REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY
a.

Temporarily replace the double lock door control relay assembly with a new or normally functioning one (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL RELAY>REMOVAL).



NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1249 is not output.




OK

END (DOUBLE LOCK DOOR CONTROL RELAY IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)