Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053728 POWER DISTRIBUTION _0261028 MAIN BODY ECU A

POWER DISTRIBUTION  MAIN BODY ECU  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 67920 2.REMOVE DOOR SCUFF PLATE ASSEMBLY LH

a.

for 5 Door:

Remove the door scuff plate assembly LH (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 5 Door)>REMOVAL).


b.

for 3 Door:

Remove the door scuff plate assembly LH (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 3 Door)>REMOVAL).


Hide 62112 3.REMOVE COWL SIDE TRIM BOARD LH

a.

for 5 Door:

Remove the cowl side trim board LH (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 5 Door)>REMOVAL).


b.

for 3 Door:

Remove the cowl side trim board LH (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 3 Door)>REMOVAL).


Hide 55606 4.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55471A 6.REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT (for LHD)

Hide 55476C 7.REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)

Hide 55480D 8.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 55045 9.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hide 73900 10.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 11.REMOVE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

a.
E197200

Disconnect the 3 connectors.


b.
U116477E06
2.344,0.875 2.604,1.115 0.26,0.24 10 true (1) 2.417,1.479 2.677,1.708 0.26,0.229 10 true (1) 2.802,2.396 3.021,2.646 0.219,0.25 10 true (2)

Detach the 2 claws and disconnect the 2 connectors labeled (1) as shown in the illustration.


c.

Disconnect the connector labeled (2).


d.
E197202

Remove the bolt and 2 nuts and disconnect the driver side junction block assembly.


e.
E178377

Detach the claw and disconnect the connector as shown in the illustration.


f.
E178379

Detach the 2 claws and release the connector's lock as shown in the illustration.


g.
E178381

Detach the claw and disconnect the connector as shown in the illustration.


h.

Remove the driver side junction block assembly.


Hide 89221 12.REMOVE MULTIPLEX NETWORK BODY ECU

a.
E183106E01
0.195,2.79 0.388,2.981 0.193,0.191 10 *1 0.45,2.332 0.587,2.93 false 0.355,2.257 0.282,2.761 false 0.499,2.94 0.692,3.131 0.193,0.191 10 *2 2.375,2.2 2.879,2.031 false 2.912,1.935 3.105,2.126 0.193,0.191 10 *3

Press the claw of the junction block as shown in the illustration to release the lock.

Text in Illustration
*1 Multiplex Network Body ECU
*2 Driver Side Junction Block
*3 Protective Tape


b.

With the junction block lock released, insert a screwdriver with its tip wrapped with protective tape horizontally between the multiplex network body ECU and junction block.

NOTICE:

Use a screwdriver with a radius of between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).



c.
E183107

Using the screwdriver, carefully raise the multiplex network body ECU until the connector becomes disengaged.

NOTICE:

Do not twist the screwdriver to raise the multiplex network body ECU.



d.
B195950E01
0.587,0.6 0.790,0.814 0.202,0.214 10 (1) 1.56,1.161 1.762,1.375 0.202,0.214 10 (2)

Raise the multiplex network body ECU as shown by arrow (1), and then pull it out as shown by arrow (2) in the illustration.

NOTICE:

Do not touch the ECU connector.