Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261030 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1206  P/W Master Switch Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the multiplex network master switch assembly and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B1206 No communication between the multiplex network master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Multiplex network master switch assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

C211493E01
5.406,0.378 5.720,0.546 0.314,0.168 10 LIN1 5.144,0.297 5.338,0.465 0.195,0.168 10 17 1.543,0.378 1.857,0.546 0.314,0.168 10 LIN2 1.956,0.297 2.150,0.465 0.195,0.168 10 16 5.406,0.813 5.543,0.981 0.138,0.168 10 B 5.144,0.731 5.338,0.899 0.195,0.168 10 11 4.57,0.937 5.048,1.105 0.478,0.168 10 DOOR 3.187,0.814 3.982,0.982 0.794,0.168 10 from Battery 5.406,1.255 5.764,1.423 0.358,0.168 10 GND 5.144,1.174 5.338,1.342 0.195,0.168 10 12 0.773,0.869 1.065,1.037 0.292,0.168 10 A 0.773,1.039 2.443,1.487 1.670,0.448 10 Main Body ECU (Multiplex Network Body ECU) 4.697,1.73 5.406,1.898 0.709,0.168 10 K4*1, J9*2 0.07,2.205 0.779,2.373 0.709,0.168 10 *1: for LHD 0.07,2.447 0.837,2.615 0.767,0.168 10 *2: for RHD 4.697,1.893 6.798,2.258 2.101,0.365 10 Multiplex Network Master Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.



HINT:

When communication between the multiplex network master switch and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1206 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MULTIPLEX NETWORK MASTER SWITCH)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MULTIPLEX NETWORK MASTER SWITCH)
a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Disconnect the K4*1 or J9*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
A-16 (LIN2) - K4-17 (LIN1) Always Below 1 Ω
A-16 (LIN2) or K4-17 (LIN1) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
A-16 (LIN2) - J9-17 (LIN1) Always Below 1 Ω
A-16 (LIN2) or J9-17 (LIN1) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - BATTERY AND BODY GROUND)
a.
U170163E02
1.042,1.406 0.833,1.625 0.833,1.625 0.698,1.625 true 1.198,1.406 1.083,1.844 1.083,1.844 0.948,1.844 true 0.063,0.031 0.271,0.25 0.208,0.219 10 false *a 0.542,1.531 0.688,1.708 0.146,0.177 10 false B 0.542,1.771 0.875,1.948 0.333,0.177 10 false GND 2.021,0.281 2.26,0.458 0.24,0.177 10 false J9 2.438,0.26 2.635,0.438 0.198,0.177 10 false *B 1.104,0.292 1.344,0.469 0.24,0.177 10 false K4 1.5,0.281 1.698,0.458 0.198,0.177 10 false *A

Disconnect the K4*1 or J9*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
K4-12 (GND) - Body ground Always Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition
J9-12 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition
K4-11 (B) - Body ground Always 11 to 14 V

for RHD:
Tester Connection Condition Specified Condition
J9-11 (B) - Body ground Always 11 to 14 V



Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Multiplex Network Master Switch Assembly)


OK

5.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Temporarily replace the multiplex network master switch assembly with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).



NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1206 is not output.




OK

END (MULTIPLEX NETWORK MASTER SWITCH IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)