Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261030 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2786  No Response from Steering Lock ECU  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU and steering lock actuator assembly (steering lock ECU) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2786 LIN communication between the certification ECU and steering lock ECU stops for 10 seconds or more.
·

Steering lock actuator assembly (steering lock ECU)

·

Certification ECU

·

Harness or connector



WIRING DIAGRAM

C358519E02
1.542,0.688 2,0.885 0.458,0.198 10 false LIN 5.365,0.677 5.823,0.875 0.458,0.198 10 false LIN 1,1.25 1.458,1.448 0.458,0.198 10 false G38 0.99,1.438 2.115,1.656 1.125,0.219 10 false Certification ECU 1.917,0.542 2.229,0.74 0.313,0.198 10 false 29 5.125,0.563 5.438,0.76 0.313,0.198 10 false 5 2.813,1.219 3.646,1.469 0.833,0.25 10 false from Battery 2.646,1.802 3.646,2.01 1,0.208 10 false from IG2 Relay 4.156,1.406 5.031,1.604 0.875,0.198 10 false STRG LOCK 4.448,1.99 4.906,2.188 0.458,0.198 10 false IGN 4.708,2.854 5.021,3.063 0.313,0.208 10 false G35 5.365,1.229 5.521,1.427 0.156,0.198 10 false B 5.375,1.813 5.833,2.01 0.458,0.198 10 false IG2 5.354,2.354 5.813,2.552 0.458,0.198 10 false GND 5.125,1.115 5.281,1.313 0.156,0.198 10 false 7 5.125,1.688 5.281,1.885 0.156,0.198 10 false 6 5.135,2.208 5.292,2.406 0.156,0.198 10 false 1 4.708,3.031 6.781,3.427 2.073,0.396 10 false Steering Lock Actuator Assembly (Steering Lock ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.



HINT:

When communication between the steering lock ECU and certification ECU stops, DTC B2785 is also stored.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2786 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STEERING LOCK ECU)
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STEERING LOCK ECU)
a.

Disconnect the G38 certification ECU connector.


b.

Disconnect the G35 steering lock actuator assembly (steering lock ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G38-29 (LIN) - G35-5 (LIN) Always Below 1 Ω
G38-29 (LIN) or G35-5 (LIN) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - BATTERY AND BODY GROUND)
a.
U170167E02
1.25,1.208 0.958,1.708 0.958,1.708 0.813,1.708 true 2.208,1.198 2.521,1.604 2.521,1.604 2.667,1.604 true 2.042,1.208 2.188,1.927 2.188,1.927 2.323,1.927 true 0.052,0.042 0.229,0.24 0.177,0.198 10 false *a 2.74,1.531 2.885,1.708 0.146,0.177 10 false B 0.469,1.635 0.802,1.813 0.333,0.177 10 false GND 0.542,1.031 0.875,1.208 0.333,0.177 10 false G35 2.417,1.854 2.688,2.031 0.271,0.177 10 false IG2

Disconnect the G35 steering lock actuator assembly (steering lock ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G35-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G35-6 (IG2) - Body ground Ignition switch ON 11 to 14 V
G35-7 (B) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Steering Lock Actuator [Steering Lock ECU])


OK

5.REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)
a.

Temporarily replace the steering lock actuator assembly (steering lock ECU) with a new one.




NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2786 is not output.




OK

END (STEERING LOCK ECU IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU