Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261030 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2661  Lost Communication with Combination Meter  


DESCRIPTION

This DTC is stored when LIN communication between the driving support switch control ECU and combination meter assembly stops 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2661 No communication between the driving support switch control ECU and combination meter assembly for 10 seconds or more.
·

Driving support switch control ECU

·

Combination meter assembly

·

Harness or connector



WIRING DIAGRAM

C358519E01
0.135,2.99 1.875,3.198 1.74,0.208 10 false *1: for Manual Transmission 0.135,3.354 2.115,3.583 1.979,0.229 10 false *2: for Automatic Transmission 0.729,1.26 1.75,1.5 1.021,0.24 10 false G76*1, G162*2 0.75,1.458 2.177,1.865 1.427,0.406 10 false Driving Support Switch Control ECU 1.51,0.677 1.969,0.875 0.458,0.198 10 false LIN 1.906,0.51 2.615,0.729 0.708,0.219 10 false 5*1, 16*2 2.833,1.208 3.698,1.427 0.865,0.219 10 false from Battery 2.677,1.792 3.656,2.031 0.979,0.24 10 false from IG2 Relay 4.354,1.385 4.875,1.615 0.521,0.229 10 false ECU-B 4.313,2 4.885,2.208 0.573,0.208 10 false GAUGE 4.75,3.052 6.625,3.281 1.875,0.229 10 false Combination Meter Assembly 4.74,2.875 5.052,3.073 0.313,0.198 10 false G6 5.031,0.531 5.344,0.729 0.313,0.198 10 false 37 5.042,1.094 5.354,1.292 0.313,0.198 10 false 26 5.042,1.667 5.354,1.865 0.313,0.198 10 false 28 5.052,2.208 5.365,2.406 0.313,0.198 10 false 21 5.375,0.688 5.833,0.885 0.458,0.198 10 false LIN 5.385,1.229 5.844,1.427 0.458,0.198 10 false B 5.385,1.802 5.844,2 0.458,0.198 10 false IG+ 5.375,2.344 5.833,2.542 0.458,0.198 10 false E2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2661 is not output.




OK

USE SIMULATION METHOD TO CHECK

NG

3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT SWITCH CONTROL ECU - COMBINATION METER)
3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT SWITCH CONTROL ECU - COMBINATION METER)
a.

for Manual Transmission

i.

Disconnect the G76 driving support switch control ECU connector.


ii.

Disconnect the G6 combination meter assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G76-5 (LIN) - G6-37 (LIN) Always Below 1 Ω
G76-5 (LIN) or G6-37 (LIN) - Body ground Always 10 kΩ or higher




b.

for Automatic Transmission

i.

Disconnect the G162 driving support switch control ECU connector.


ii.

Disconnect the G6 combination meter assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G162-16 (LIN) - G6-37 (LIN) Always Below 1 Ω
G162-16 (LIN) or G6-37 (LIN) - Body ground Always 10 kΩ or higher





OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BATTERY AND BODY GROUND)
a.
U170645E01
0.282,1.238 0.501,1.425 0.219,0.188 10 G6 1.503,1.461 1.744,1.816 1.744,1.816 1.877,1.816 false 0.871,1.463 0.648,1.77 0.648,1.77 0.516,1.77 false 1.888,1.729 2.151,1.879 0.262,0.150 10 IG+ 1.317,1.461 1.434,1.968 1.434,1.968 1.566,1.968 false 1.578,1.89 1.711,2.040 0.134,0.150 10 B 0.242,1.696 0.454,1.846 0.212,0.150 10 E2 0.047,0.013 0.214,0.187 0.168,0.174 10 *a

Disconnect the G6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-21 (E2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G6-26 (B) - Body ground Always 11 to 14 V
G6-28 (IG+) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


OK

5.REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE COMBINATION METER ASSEMBLY
a.

Temporarily replace the combination meter assembly with a new or normally functioning one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).



NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC

OK

END (COMBINATION METER IS DEFECTIVE)

NG

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU