Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Main Body ECU Communication Stop Mode Either condition is met:
·

"Main Body" is not displayed on "Bus Check".

·

"Main Body ECU Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside main body ECU (multiplex network body ECU)

·

Main body ECU (multiplex network body ECU) CAN branch wire or connector

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

E346821E02
0.333,1.344 0.948,1.542 0.615,0.198 10 false G94 0.323,1.5 1.906,1.833 1.583,0.333 10 false No. 3 Junction Connector 1.667,0.844 2.281,1.042 0.615,0.198 10 false 14 1.698,0.406 2.313,0.604 0.615,0.198 10 false 3 5.344,0.521 5.958,0.719 0.615,0.198 10 false G64 5.385,0.313 6,0.51 0.615,0.198 10 false 14 5.708,0.521 6.323,0.719 0.615,0.198 10 false CANH 5.354,0.948 5.969,1.146 0.615,0.198 10 false G64 5.396,0.74 6.01,0.938 0.615,0.198 10 false 13 5.708,0.938 6.323,1.135 0.615,0.198 10 false CANL 5.396,1.74 6.01,1.938 0.615,0.198 10 false A 5.406,2.208 6.021,2.406 0.615,0.198 10 false A 5.406,2.677 6.021,2.875 0.615,0.198 10 false A 5.406,3.146 6.021,3.344 0.615,0.198 10 false A 5.417,3.823 6.031,4.021 0.615,0.198 10 false A 5.354,4.281 5.969,4.479 0.615,0.198 10 false G63 5.698,1.729 6.313,1.927 0.615,0.198 10 false BECU 5.708,2.188 6.323,2.385 0.615,0.198 10 false ALTB 5.708,2.677 6.323,2.875 0.615,0.198 10 false IG 5.719,3.146 6.333,3.344 0.615,0.198 10 false ACC 5.385,1.51 6,1.708 0.615,0.198 10 false 30 5.385,2 6,2.198 0.615,0.198 10 false 31 5.375,2.469 5.99,2.667 0.615,0.198 10 false 32 5.375,2.948 5.99,3.146 0.615,0.198 10 false 29 4.26,1.552 4.875,1.75 0.615,0.198 10 false ECU-B 4.188,2.063 4.802,2.26 0.615,0.198 10 false D/L NO. 2 4.073,2.521 5.094,2.76 1.021,0.24 10 false ECU-IG NO. 2 4.313,3.021 5.333,3.26 1.021,0.24 10 false ACC 2.604,1.708 3.646,1.927 1.042,0.219 10 false from Battery 2.594,2.188 3.635,2.406 1.042,0.219 10 false from Battery 2.042,2.677 3.5,2.927 1.458,0.25 10 false from IG1 NO. 1 Relay 2.375,3.125 3.833,3.375 1.458,0.25 10 false from ACC Relay 5.698,3.823 6.313,4.021 0.615,0.198 10 false GND1 5.385,3.615 6,3.813 0.615,0.198 10 false 11 5.438,4.073 6.052,4.271 0.615,0.198 10 false 3 5.729,4.281 6.344,4.479 0.615,0.198 10 false GND2 5.24,4.792 6.927,5.198 1.688,0.406 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU CAN BRANCH WIRE)
a.
U148349E04
1.271,0.469 1.365,0.469 1.365,0.469 1.604,1.188 true 1.531,1.198 1.042,0.719 1.042,0.719 0.958,0.719 true 0.052,0 0.292,0.188 0.24,0.188 10 false *a 0.542,0.635 0.969,0.792 0.427,0.156 10 false CANH 0.896,0.396 1.302,0.552 0.406,0.156 10 false CANL 0.458,1.125 0.792,1.281 0.333,0.156 10 false G64

Disconnect the G64 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G64-14 (CANH) - G64-13 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE MAIN BODY ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


U148500E04
5.865,0.531 5.927,0.531 5.927,0.531 6.167,1.167 true 3.781,0.531 3.844,0.531 3.844,0.531 4.083,1.167 true 6.427,0.531 6.365,0.531 6.365,0.531 6.271,1.167 true 6.667,0.844 6.594,0.844 6.594,0.844 6.396,1.167 true 0.594,0.552 0.656,0.552 0.656,0.552 0.854,0.917 true 6.25,1.542 6.323,1.542 6.323,1.542 6.51,1.208 true 3.375,0.458 3.792,0.625 0.417,0.167 10 false GND1 5.542,0.458 5.854,0.625 0.313,0.167 10 false ACC 6.479,0.458 6.917,0.625 0.438,0.167 10 false BECU 6.708,0.76 7.094,0.927 0.385,0.167 10 false ALTB 2.406,0.021 2.604,0.25 0.198,0.229 10 false *b 0.021,0.021 0.219,0.25 0.198,0.229 10 false *a 0.198,0.479 0.625,0.646 0.427,0.167 10 false GND2 0.177,0.906 0.49,1.073 0.313,0.167 10 false G63 2.417,1.083 2.552,1.25 0.135,0.167 10 false A 6.083,1.458 6.26,1.625 0.177,0.167 10 false IG

Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])


b.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G63-3 (GND2) - Body ground Always Below 1 Ω
A-11 (GND1) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A-32 (IG) - Body ground Engine switch on (IG) 11 to 14 V
A-31 (ALTB) - Body ground Always 11 to 14 V
A-30 (BECU) - Body ground Always 11 to 14 V
A-29 (ACC) - Body ground Engine switch on (ACC) 11 to 14 V




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR