Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  Navigation ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Navigation ECU Communication Stop Mode Either condition is met:
·

"Display and Navigation (AVN1)" is not displayed on "Bus Check".

·

"Navigation ECU Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside of navigation receiver assembly

·

Navigation receiver assembly CAN branch wire or connector

·

Navigation receiver assembly



For vehicles with a navigation system (for navigation receiver type).)


WIRING DIAGRAM

C334435E01
5.175,4.196 5.452,4.333 0.276,0.137 10 H54 5.175,3.615 5.452,3.752 0.276,0.137 10 H56 5.175,3.02 5.452,3.157 0.276,0.137 10 H54 5.175,2.431 5.452,2.569 0.276,0.137 10 H54 5.175,0.842 5.452,0.979 0.276,0.137 10 H56 5.175,1.435 5.452,1.573 0.276,0.137 10 H56 5.365,4.902 6.649,5.216 1.283,0.313 10 Navigation Receiver Assembly 0.382,1.775 2.214,1.913 1.832,0.137 10 G100 1.62,1.341 1.799,1.478 0.179,0.137 10 13 1.62,0.752 1.771,0.890 0.151,0.137 10 2 5.224,1.22 5.404,1.358 0.179,0.137 10 10 5.259,0.62 5.370,0.757 0.111,0.137 10 9 5.259,2.191 5.370,2.328 0.111,0.137 10 4 5.259,2.789 5.370,2.926 0.111,0.137 10 3 5.259,3.382 5.370,3.519 0.111,0.137 10 1 5.259,3.951 5.370,4.089 0.111,0.137 10 7 5.613,1.423 6.098,1.560 0.485,0.137 10 CANL 5.613,0.835 6.098,0.972 0.485,0.137 10 CANH 5.613,3.02 6.098,3.158 0.485,0.137 10 ACC1 5.613,3.613 6.098,3.751 0.485,0.137 10 IG 5.613,2.422 6.098,2.560 0.485,0.137 10 +B1 5.613,4.197 6.098,4.334 0.485,0.137 10 GND1 0.382,1.939 2.381,2.076 1.998,0.137 10 No. 2 Junction Connector 1.321,3.006 2.352,3.144 1.031,0.137 10 from ACC Relay 1.017,3.59 2.349,3.727 1.332,0.137 10 from IG1 NO.1 Relay 1.578,2.419 2.354,2.556 0.776,0.137 10 from Battery 3.313,2.273 3.988,2.420 0.674,0.147 10 RAD NO.1 3.206,3.464 4.093,3.611 0.887,0.147 10 ECU-IG NO.2 3.488,2.868 3.815,3.015 0.327,0.147 10 ACC

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY CAN BRANCH WIRE)
a.
U170266E01
0.082,0.083 0.286,0.253 0.205,0.170 10 *a 1.581,0.371 1.855,0.512 0.274,0.140 10 H56 2.039,1.299 2.26,1.825 2.26,1.825 2.366,1.825 false 1.908,1.299 1.687,1.825 1.687,1.825 1.581,1.825 false 1.079,1.75 1.490,1.889 0.411,0.139 10 CANH 2.398,1.75 2.809,1.889 0.411,0.139 10 CANL

Disconnect the H56 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H56-9 (CANH) - H56-10 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE NAVIGATION RECEIVER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U170331E01
0.064,0.06 0.269,0.230 0.205,0.170 10 *a 2.01,0.866 2.297,0.554 2.297,0.554 2.402,0.554 false 2.184,0.98 2.383,1.19 2.383,1.19 2.488,1.19 false 1.599,1.152 1.351,1.459 1.351,1.459 1.246,1.459 false 0.449,2.359 0.613,2.498 0.165,0.139 10 IG 0.743,1.384 1.154,1.522 0.411,0.139 10 GND1 2.505,1.113 2.916,1.251 0.411,0.139 10 +B1 2.423,0.477 2.835,0.615 0.411,0.139 10 ACC1 0.651,2.432 0.786,2.432 0.786,2.432 0.981,2.605 false 1.551,1.826 1.832,1.963 0.281,0.137 10 H56 1.551,0.215 1.832,0.352 0.281,0.137 10 H54

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the H54 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-7 (GND1) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H54-4 (+B1) - Body ground Always 11 to 14 V
H54-3 (ACC1) - Body ground Engine switch on (ACC) 11 to 14 V
H56-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR