Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  U0208  Lost Communication with "Seat Control Module A"  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0208 There is no communication from the front power seat switch LH.
·

Power source or inside front power seat switch LH

·

Front power seat switch LH CAN branch wire or connector

·

Front power seat switch LH



For vehicles with a seat position memory.


WIRING DIAGRAM

C348087E01
0.406,2.031 2.188,2.302 1.781,0.271 10 false No. 3 Junction Connector 0.396,1.875 2.177,2.146 1.781,0.271 10 false G96 2,0.927 2.49,1.135 0.49,0.208 10 false 2 1.99,1.344 2.479,1.552 0.49,0.208 10 false 13 2.479,2.24 3.5,2.51 1.021,0.271 10 false from Battery 2.49,2.719 3.51,2.99 1.021,0.271 10 false from Battery 3.969,2.083 4.813,2.292 0.844,0.208 10 false P/SEAT FL 4.104,2.563 4.698,2.844 0.594,0.281 10 false ECU-B 4.802,3.906 6.802,4.156 2,0.25 10 false Front Power Seat Switch LH 5.01,1.063 5.323,1.26 0.313,0.198 10 false b5 5.01,1.5 5.323,1.698 0.313,0.198 10 false b5 5,2.74 5.313,2.938 0.313,0.198 10 false b5 5,2.25 5.313,2.448 0.313,0.198 10 false b4 5.01,3.25 5.323,3.448 0.313,0.198 10 false b4 5.292,1.063 5.906,1.26 0.615,0.198 10 false CANP 5.302,1.5 5.917,1.698 0.615,0.198 10 false CANN 5.271,2.26 5.885,2.458 0.615,0.198 10 false +B 5.302,2.76 5.917,2.958 0.615,0.198 10 false SYSB 5.292,3.25 5.906,3.448 0.615,0.198 10 false GND 5.021,0.885 5.333,1.083 0.313,0.198 10 false 8 5.031,1.292 5.344,1.49 0.313,0.198 10 false 7 5.052,2.042 5.365,2.24 0.313,0.198 10 false 7 5.052,3.031 5.365,3.229 0.313,0.198 10 false 2 5,2.542 5.49,2.75 0.49,0.208 10 false 12

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (FRONT POWER SEAT SWITCH LH CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (FRONT POWER SEAT SWITCH LH CAN BRANCH WIRE)
a.
U148774E03
2.51,1.781 2.448,1.781 2.448,1.781 2.313,1.594 true 2.51,1.208 2.448,1.208 2.448,1.208 2.229,1.552 true 0.073,0.052 0.25,0.219 0.177,0.167 10 false *a 2.552,1.708 2.99,1.875 0.438,0.167 10 false CANN 2.563,1.125 3,1.292 0.438,0.167 10 false CANP 1.271,1.302 1.542,1.469 0.271,0.167 10 false b5

Disconnect the b5 front power seat switch LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
b5-8 (CANP) - b5-7 (CANN) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Front Power Seat Switch LH)



OK

3.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE FRONT POWER SEAT SWITCH LH CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)

3.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - BATTERY AND BODY GROUND)
a.
U148775E03
0.75,1.813 0.813,1.813 0.813,1.813 1.375,1.406 true 1.792,2.021 1.854,2.021 1.854,2.021 2.073,1.583 true 0.76,0.802 0.823,0.802 0.823,0.802 1.375,1.208 true 0.281,0.104 0.458,0.271 0.177,0.167 10 false *a 0.542,1.74 0.76,1.906 0.219,0.167 10 false +B 1.385,1.948 1.823,2.115 0.438,0.167 10 false SYSB 0.271,1.156 0.542,1.323 0.271,0.167 10 false b4 2.927,1.177 3.198,1.344 0.271,0.167 10 false b5 0.417,0.729 0.771,0.896 0.354,0.167 10 false GND

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the b4 front power seat switch LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b4-2 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
b4-7 (+B) - Body ground Always 11 to 14 V
b5-12 (SYSB) - Body ground Always 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Front Power Seat Switch LH)


OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR