Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  U1115  Lost Communication with Tilt and Telescopic Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U1115 There is no communication from the multiplex tilt and telescopic ECU.
·

Power source or inside multiplex tilt and telescopic ECU

·

Multiplex tilt and telescopic ECU CAN branch wire or connector

·

Multiplex tilt and telescopic ECU



For vehicles with power tilt and power telescopic steering column only.


WIRING DIAGRAM

E346818E02
0.354,1.969 0.969,2.167 0.615,0.198 10 false G96 0.344,2.146 1.948,2.448 1.604,0.302 10 false No. 3 Junction Connector 1.948,0.958 2.563,1.156 0.615,0.198 10 false 3 1.938,1.365 2.552,1.563 0.615,0.198 10 false 14 5.063,0.938 5.677,1.135 0.615,0.198 10 false 5 5.042,1.385 5.656,1.583 0.615,0.198 10 false 14 5.281,1.052 5.896,1.25 0.615,0.198 10 false CANP 5.281,1.479 5.896,1.677 0.615,0.198 10 false CANN 5.281,1.969 5.896,2.167 0.615,0.198 10 false +B 5.281,2.396 5.896,2.594 0.615,0.198 10 false ECUB 5.302,2.781 5.917,2.979 0.615,0.198 10 false IG 5.271,3.26 5.885,3.458 0.615,0.198 10 false GND 5.042,3.125 5.656,3.323 0.615,0.198 10 false 11 4.75,3.802 5.365,4 0.615,0.198 10 false G116 4.75,3.948 6.875,4.24 2.125,0.292 10 false Multiplex Tilt and Telescopic ECU 5.063,2.708 5.677,2.906 0.615,0.198 10 false 8 5.083,2.313 5.698,2.51 0.615,0.198 10 false 9 5.083,1.896 5.698,2.094 0.615,0.198 10 false 2 4.333,1.844 4.948,2.042 0.615,0.198 10 false TI&TE 4.323,2.271 4.938,2.469 0.615,0.198 10 false ECU-B 3.948,2.656 4.802,2.854 0.854,0.198 10 false ECU-IG NO.1 1.979,2.813 3.302,3.042 1.323,0.229 10 false from IG1 NO. 1 Relay 2.542,2.375 3.865,2.604 1.323,0.229 10 false from Battery 2.573,1.969 3.896,2.198 1.323,0.229 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK OPEN IN CAN BUS WIRE (MULTIPLEX TILT AND TELESCOPIC ECU BRANCH WIRE)
2.CHECK OPEN IN CAN BUS WIRE (MULTIPLEX TILT AND TELESCOPIC ECU BRANCH WIRE)
a.
U148171E02
2.198,1.365 2.594,1.063 2.594,1.063 2.729,1.063 false 2.198,1.521 2.573,1.875 2.573,1.875 2.708,1.875 false 0.063,0 0.24,0.208 0.177,0.208 10 false *a 2.75,1.802 3.188,1.969 0.438,0.167 10 false CANP 2.76,0.979 3.198,1.156 0.438,0.177 10 false CANN 1.208,1.552 1.594,1.729 0.385,0.177 10 false G116

Disconnect the G116 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G116-5 (CANP) - G116-14 (CANN) Engine switch off 54 to 64 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)



OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE MULTIPLEX TILT AND TELESCOPIC ECU CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY AND BODY GROUND)
a.
U148172E03
1.948,1.51 1.729,1.271 1.729,1.271 1.604,1.271 false 2.417,1.563 2.573,1.885 2.573,1.885 2.708,1.885 false 2.427,1.396 2.656,1.115 2.656,1.115 2.792,1.115 false 1.865,1.563 1.75,1.958 1.75,1.958 1.615,1.958 false 0.063,0 0.24,0.208 0.177,0.208 10 false *a 1.198,1.51 1.583,1.688 0.385,0.177 10 false G116 1.427,1.208 1.625,1.375 0.198,0.167 10 false IG 2.729,1.802 2.948,1.979 0.219,0.177 10 false +B 2.833,1.042 3.188,1.208 0.354,0.167 10 false GND 1.219,1.885 1.656,2.063 0.438,0.177 10 false ECUB

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G116-11 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G116-2 (+B) - Body ground Always 11 to 14 V
G116-9 (ECUB) - Body ground Always 11 to 14 V
G116-8 (IG) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR