Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  U1002  Lost Communication with Gateway Module (Sensor Bus)  


DESCRIPTION

·

The driving support ECU assembly stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the parking assist bus.

·

When the driving support ECU assembly receives a response signal from the ECUs connected to the parking assist bus, the driving support ECU assembly recognizes and memorizes that the ECU is connected to the parking assist bus. Based on this memorized data, the driving support ECU assembly monitors for malfunctions in the ECUs connected to the parking assist bus when communicating with those ECUs. If the driving support ECU assembly cannot receive response signals from the ECUs that have been memorized as those connected to the parking assist bus, the driving support ECU assembly determines that a malfunction exists.

·

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).


DTC Code DTC Detection Condition Trouble Area
U1002 Lost communication with the gateway module (parking assist bus).
·

Parking assist bus circuit

·

Driving support ECU assembly CAN main wire or connector

·

Millimeter wave radar sensor assembly CAN main wire or connector

·

Driving support ECU assembly

·

Millimeter wave radar sensor assembly



For vehicles with a pre-crash safety system.


WIRING DIAGRAM

C295836E02
1.802,0.646 2.063,0.781 0.26,0.135 10 false 4 1.802,1.094 2,1.323 0.198,0.229 10 false 3 1.365,0.656 1.844,0.854 0.479,0.198 10 false CA1P 1.365,1.365 1.854,1.563 0.49,0.198 10 false CA1N 0.385,1.563 0.854,1.729 0.469,0.167 10 false A15 0.385,1.708 2.25,2.208 1.865,0.5 10 false Millimeter Wave Radar Sensor Assembly 5.24,0.646 5.51,0.854 0.271,0.208 10 false 40 5.24,1.094 5.521,1.302 0.281,0.208 10 false 18 5.521,0.656 6.01,0.844 0.49,0.188 10 false CA1P 5.521,1.344 6.021,1.552 0.5,0.208 10 false CA1N 4.865,1.552 5.292,1.719 0.427,0.167 10 false G119 4.865,1.719 6.885,2.083 2.021,0.365 10 false Driving Support ECU Assembly

CAUTION / NOTICE / HINT

HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT)
2.CHECK FOR CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT)
a.
U170256E03
0.552,0.833 0.688,0.833 0.688,0.833 0.844,0.979 false 0.583,1.365 0.708,1.365 0.708,1.365 0.885,1.146 false 1.625,2.521 1.448,2.052 1.448,2.052 1.271,2.052 false 2.208,2.917 2.375,3.125 2.375,3.125 2.469,3.125 false 0.177,1.292 0.625,1.521 0.448,0.229 10 false CA1P 0.146,0.75 0.604,0.948 0.458,0.198 10 false CA1N 1.5,0.177 1.875,0.417 0.375,0.24 10 false G119 0.448,2.698 0.833,2.958 0.385,0.26 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 0.979,1.969 1.219,2.146 0.24,0.177 10 false CG 2.469,3.031 2.906,3.208 0.438,0.177 10 false BAT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition resistance: Malfunction
G119-40 (CA1P) - G119-18 (CA1N) Engine switch off 54 to 69 Ω Below 53 Ω: Short in line
G119-40 (CA1P) - G119-18 (CA1N) Engine switch off 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
G119-40 (CA1P) - G48-16 (BAT) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
G119-18 (CA1N) - G48-16 (BAT) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
G119-40 (CA1P) - G48-4 (CG) Engine switch off 200 Ω or higher Below 200 Ω: Ground short
G119-18 (CA1N) - G48-4 (CG) Engine switch off 200 Ω or higher Below 200 Ω: Ground short


Text in Illustration
*a Component with harness connected
(Driving Support ECU Assembly)
*b Front view of DLC3

Result
Result Proceed to
NG
·

Open in CAN main wire


A
NG
·

Short in line

·

+B short

·

Ground short


B
OK C



A

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (DRIVING SUPPORT ECU ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

B

6.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

C

9.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)
3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (DRIVING SUPPORT ECU ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.
U170206E03
0.823,1.771 0.979,1.771 0.979,1.771 1.125,1.906 false 0.844,2.26 1.031,2.26 1.031,2.26 1.156,2.042 false 0.427,1.698 0.813,1.875 0.385,0.177 10 false CA1N 0.448,2.198 0.833,2.375 0.385,0.177 10 false CA1P 2.885,1.469 3.292,1.635 0.406,0.167 10 false G119 0.063,0.01 0.271,0.188 0.208,0.177 10 false *a

Disconnect the G119 driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G119-40 (CA1P) - G119-18 (CA1N) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Driving Support ECU Assembly)



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

4.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the G119 driving support ECU assembly connector.



NEXT

5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.
U169953E03
1.688,1.396 2.021,0.635 2.021,0.635 2.156,0.635 false 1.854,1.396 2.448,1 2.448,1 2.604,1 false 0.135,0 0.323,0.208 0.188,0.208 10 false *a 0.292,1.313 0.583,1.479 0.292,0.167 10 false A15 2.656,0.917 3.094,1.083 0.438,0.167 10 false CA1P 2.219,0.563 2.625,0.729 0.406,0.167 10 false CA1N

Disconnect the A15 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A15-4 (CA1P) - A15-3 (CA1N) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MILLIMETER WAVE RADAR SENSOR (MILLIMETER WAVE RADAR SENSOR - DRIVING SUPPORT ECU ASSEMBLY)

6.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.
U170218E02
0.698,0.906 0.792,0.906 0.792,0.906 0.958,1.042 false 0.76,1.406 0.875,1.406 0.875,1.406 0.99,1.188 false 1.646,2.531 1.438,2.104 1.438,2.104 1.323,2.104 false 2.208,2.917 2.365,3.125 2.365,3.125 2.458,3.125 false 0.375,1.313 0.76,1.49 0.385,0.177 10 false CA1P 0.292,0.833 0.698,1.01 0.406,0.177 10 false CA1N 1.604,0.219 2.031,0.438 0.427,0.219 10 false G119 0.458,2.698 0.802,2.896 0.344,0.198 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 1.031,2.021 1.271,2.198 0.24,0.177 10 false CG 2.479,3.031 2.917,3.208 0.438,0.177 10 false BAT

Disconnect the G119 driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G119-40 (CA1P) - G119-18 (CA1N) Engine switch off 108 to 132 Ω
G119-40 (CA1P) - G48-4 (CG) Engine switch off 200 Ω or higher
G119-18 (CA1N) - G48-4 (CG) Engine switch off 200 Ω or higher
G119-40 (CA1P) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G119-18 (CA1N) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Driving Support ECU Assembly)
*b Front view of DLC3



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

7.CONNECT CONNECTOR
7.CONNECT CONNECTOR
a.

Reconnect the G119 driving support ECU assembly connector.



NEXT

8.CHECK FOR SHORT IN CAN BUS WIRES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
8.CHECK FOR SHORT IN CAN BUS WIRES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.
U170255E02
2.531,0.552 2.396,0.552 2.396,0.552 1.854,1.073 false 2.135,1.708 1.99,1.708 1.99,1.708 1.688,1.125 false 2.229,2.938 2.438,3.104 2.438,3.104 2.521,3.104 false 1.635,2.552 1.208,2.135 1.208,2.135 1.125,2.135 false 2.542,0.479 2.979,0.656 0.438,0.177 10 false CA1P 2.146,1.625 2.583,1.802 0.438,0.177 10 false CA1N 0.302,0.917 0.573,1.094 0.271,0.177 10 false A15 0.448,2.667 0.74,2.844 0.292,0.177 10 false G48 0.135,1.844 0.344,2.021 0.208,0.177 10 false *b 2.521,3 2.958,3.177 0.438,0.177 10 false BAT 0.135,0.031 0.344,0.208 0.208,0.177 10 false *a 0.833,2.042 1.063,2.219 0.229,0.177 10 false CG

Disconnect the A15 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A15-4 (CA1P) - A15-3 (CA1N) Engine switch off 108 to 132 Ω
A15-4 (CA1P) - G48-4 (CG) Engine switch off 200 Ω or higher
A15-3 (CA1N) - G48-4 (CG) Engine switch off 200 Ω or higher
A15-4 (CA1P) - G48-16 (BAT) Engine switch off 6 kΩ or higher
A15-3 (CA1N) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
*b Front view of DLC3



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MILLIMETER WAVE RADAR SENSOR (MILLIMETER WAVE RADAR SENSOR - DRIVING SUPPORT ECU ASSEMBLY)

9.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U170204E03
1.427,2.521 1.583,2.521 1.583,2.521 1.917,2.042 false 2.552,2.604 2.365,2.604 2.365,2.604 2.26,2.042 false 2.604,2.531 2.958,2.677 0.354,0.146 10 false GND 1.292,2.448 1.406,2.625 0.115,0.177 10 false B 0.385,1.896 0.76,2.073 0.375,0.177 10 false G119 0.063,0.052 0.271,0.229 0.208,0.177 10 false *a

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the G119 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G119-25 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G119-30 (B) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Driving Support ECU Assembly)


OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR