Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  U0233  Lost Communication with Blind Spot Monitor Master Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0233 There is no communication from the blind spot monitor sensor LH.
·

Power source or inside of blind spot monitor sensor LH

·

Blind spot monitor sensor LH CAN branch wire or connector

·

Blind spot monitor sensor LH



For vehicles with a blind spot monitor system.


WIRING DIAGRAM

E346816E05
0.573,1.438 1.031,1.635 0.458,0.198 10 false R47 0.542,1.604 2.135,1.958 1.594,0.354 10 false No. 6 Junction Connector 1.906,0.49 2.365,0.688 0.458,0.198 10 false 2 1.917,0.885 2.375,1.083 0.458,0.198 10 false 13 5.583,0.49 6.042,0.688 0.458,0.198 10 false 2 5.594,0.875 6.052,1.073 0.458,0.198 10 false 7 5.542,1.552 6,1.75 0.458,0.198 10 false 5 5.563,2.208 6.021,2.406 0.458,0.198 10 false 10 5.813,0.594 6.271,0.792 0.458,0.198 10 false CA1P 5.813,1.031 6.271,1.229 0.458,0.198 10 false CA1N 5.813,1.688 6.271,1.885 0.458,0.198 10 false BLB 5.792,2.354 6.25,2.552 0.458,0.198 10 false BLGD 4.677,1.542 5.135,1.74 0.458,0.198 10 false IG1 2.354,1.677 3.948,2.031 1.594,0.354 10 false from IG1 NO. 1 Relay 5.5,2.729 5.958,2.927 0.458,0.198 10 false R42 5.521,2.896 6.667,3.26 1.146,0.365 10 false Blind Spot Monitor Sensor LH

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR LH CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR LH CAN BRANCH WIRE)
a.
U116347E01
1.578,0.281 1.850,0.420 0.272,0.139 10 R42 0.391,0.624 0.779,0.762 0.388,0.139 10 CA1P 0.391,1.707 0.779,1.845 0.388,0.139 10 CA1N 0.052,0.041 0.365,0.180 0.314,0.139 10 *a 1.51,1.137 1.023,0.699 1.023,0.699 0.874,0.699 false 1.51,1.344 1.023,1.782 1.023,1.782 0.874,1.782 false

Disconnect the R42 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
R42-2 (CA1P) - R42-7 (CA1N) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE BLIND SPOT MONITOR SENSOR LH CAN BRANCH WIRE OR CONNECTOR (CA1P, CA1N)

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY AND BODY GROUND)
a.
U116348E01
1.578,0.281 1.850,0.420 0.272,0.139 10 R42 2.664,0.624 3.052,0.762 0.388,0.139 10 BLB 2.664,1.707 3.118,1.845 0.454,0.139 10 BLGD 0.052,0.041 0.365,0.180 0.314,0.139 10 *a 1.997,1.137 2.484,0.699 2.484,0.699 2.633,0.699 false 1.997,1.344 2.484,1.782 2.484,1.782 2.633,1.782 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R42-10 (BLGD) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R42-5 (BLB) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR