Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  U029D/A2  Lost Communication with NOx Sensor "A"  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U029D/A2 There is no communication from the nitrogen oxides sensor.
·

Power source or inside nitrogen oxides sensor

·

Nitrogen oxides sensor CAN branch wire or connector

·

Nitrogen oxides sensor



For vehicles with a urea SCR system.


WIRING DIAGRAM

C329299E04
5.313,1.052 5.875,1.271 0.563,0.219 10 false CAN+ 5.313,1.49 5.875,1.708 0.563,0.219 10 false CAN- 5.313,3.25 5.875,3.469 0.563,0.219 10 false GND 5.313,2.417 5.875,2.635 0.563,0.219 10 false BATT 5.01,0.917 5.24,1.135 0.229,0.219 10 false 4 5.01,1.385 5.24,1.604 0.229,0.219 10 false 3 5.01,2.313 5.24,2.531 0.229,0.219 10 false 1 5.01,3.125 5.24,3.344 0.229,0.219 10 false 2 0.417,1.823 0.979,2.042 0.563,0.219 10 false Q41 1.99,0.917 2.219,1.135 0.229,0.219 10 false 6 1.99,1.385 2.219,1.604 0.229,0.219 10 false 17 2.031,2.417 3.51,2.635 1.479,0.219 10 false from NOx PM Relay 0.417,1.99 2.646,2.208 2.229,0.219 10 false No. 9 Junction Connector 4.885,3.875 6.5,4.094 1.615,0.219 10 false Nitrogen Oxides Sensor 4.885,3.688 5.115,3.906 0.229,0.219 10 false s6

CAUTION / NOTICE / HINT

HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAB main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (NITROGEN OXIDES SENSOR CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (NITROGEN OXIDES SENSOR CAN BRANCH WIRE)
a.
U169383E02
1.99,1.021 2.208,1.844 2.208,1.844 2.302,1.844 true 1.677,1.031 1.521,1.854 1.521,1.854 1.396,1.854 true 1.635,0.229 1.948,0.406 0.313,0.177 10 false s6 0.979,1.76 1.583,1.938 0.604,0.177 10 false CAN- 2.354,1.771 2.823,1.948 0.469,0.177 10 false CAN+ 0.094,0.031 0.563,0.208 0.469,0.177 10 false *a

Disconnect the nitrogen oxides sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
s6-4 (CAN+) - s6-3 (CAN-) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Nitrogen Oxides Sensor)



OK

3.CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE NITROGEN OXIDES SENSOR CAN BRANCH WIRE OR CONNECTOR (CAN+, CAN-)

3.CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR - BATTERY AND BODY GROUND)
a.
U169384E02
1.552,1.031 1.771,1.854 1.771,1.854 1.865,1.854 true 1.24,1.031 1.083,1.823 1.083,1.823 0.958,1.823 true 1.625,0.24 1.938,0.417 0.313,0.177 10 false s6 0.552,1.75 0.99,1.927 0.438,0.177 10 false BATT 1.917,1.771 2.385,1.948 0.469,0.177 10 false GND 0.135,0.073 0.604,0.25 0.469,0.177 10 false *a

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s6-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
s6-1 (BATT) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Nitrogen Oxides Sensor)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR