Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261032 CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System)  Yaw Rate Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Yaw Rate Sensor Communication Stop Mode Either condition is met:
·

"Yaw Rate Sensor" is not displayed on "Bus Check".

·

"Yaw Rate Sensor Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside yaw rate sensor assembly

·

Yaw rate sensor assembly branch wire or connector

·

Yaw rate sensor assembly



WIRING DIAGRAM

E346816E07
0.552,1.427 1.01,1.625 0.458,0.198 10 false G100 0.542,1.604 2.135,1.958 1.594,0.354 10 false No. 2 Junction Connector 1.906,0.49 2.365,0.688 0.458,0.198 10 false 4 1.917,0.885 2.375,1.083 0.458,0.198 10 false 15 5.583,0.49 6.042,0.688 0.458,0.198 10 false 3 5.594,0.875 6.052,1.073 0.458,0.198 10 false 2 5.594,1.552 6.052,1.75 0.458,0.198 10 false 4 5.563,2.208 6.021,2.406 0.458,0.198 10 false 1 5.813,0.594 6.271,0.792 0.458,0.198 10 false CANH 5.813,1.031 6.271,1.229 0.458,0.198 10 false CANL 5.813,1.688 6.271,1.885 0.458,0.198 10 false IG 5.792,2.354 6.25,2.552 0.458,0.198 10 false GND 4.427,1.542 5.427,1.729 1,0.188 10 false ECU-IG NO. 1 2.281,1.677 3.688,2.021 1.406,0.344 10 false from IG1 NO. 1 Relay 5.146,2.729 5.604,2.927 0.458,0.198 10 false G52 5.146,2.885 7.073,3.146 1.927,0.26 10 false Yaw Rate Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (YAW RATE SENSOR ASSEMBLY BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (YAW RATE SENSOR ASSEMBLY BRANCH WIRE)
a.
U148302E04
0.917,1.021 1.01,1.021 1.01,1.021 1.438,1.479 false 1.167,0.573 1.281,0.573 1.281,0.573 1.563,1.469 false 0.052,0 0.229,0.177 0.177,0.177 10 false *a 0.521,0.927 0.927,1.104 0.406,0.177 10 false CANL 0.427,1.448 0.729,1.625 0.302,0.177 10 false G52 0.75,0.49 1.177,0.667 0.427,0.177 10 false CANH

Disconnect the G52 yaw rate sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G52-3 (CANH) - G52-2 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (YAW RATE SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE YAW RATE SENSOR ASSEMBLY BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (YAW RATE SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
U169959E03
0.844,1.031 0.938,1.031 0.938,1.031 1.292,1.469 false 2.375,0.76 2.24,0.76 2.24,0.76 1.708,1.469 false 0.052,0 0.229,0.177 0.177,0.177 10 false *a 0.5,0.958 0.833,1.135 0.333,0.177 10 false GND 0.438,1.448 0.74,1.625 0.302,0.177 10 false G52 2.438,0.677 2.604,0.854 0.167,0.177 10 false IG

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G52-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G52-4 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR