Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) › 2015.06–2016.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261032 CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System)  4WD Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
4WD Control ECU Communication Stop Mode Either condition is met:
·

"Four Wheel Drive Control" is not displayed on the "Bus Check".

·

"4WD Control ECU Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source circuit of four wheel drive control ECU

·

Four wheel drive control ECU branch line or connector

·

Four wheel drive control ECU



WIRING DIAGRAM

E346823E02
0.917,1.427 1.531,1.625 0.615,0.198 10 false G97 0.917,1.604 2.552,1.823 1.635,0.219 10 false No. 1 Junction Connector 1.927,0.927 2.542,1.125 0.615,0.198 10 false 13 1.958,0.49 2.573,0.688 0.615,0.198 10 false 2 5.427,0.594 6.042,0.792 0.615,0.198 10 false G53 5.458,0.406 6.073,0.604 0.615,0.198 10 false 19 5.802,0.615 6.417,0.813 0.615,0.198 10 false CANH 5.781,1.01 6.396,1.208 0.615,0.198 10 false CANL 5.427,1.031 6.042,1.229 0.615,0.198 10 false G53 5.469,0.844 6.083,1.042 0.615,0.198 10 false 20 5.438,1.906 6.052,2.104 0.615,0.198 10 false G54 5.427,2.354 6.042,2.552 0.615,0.198 10 false G54 5.51,2.146 6.125,2.344 0.615,0.198 10 false 4 5.51,1.719 6.125,1.917 0.615,0.198 10 false 3 5.792,1.906 6.406,2.104 0.615,0.198 10 false IG 5.813,2.323 6.427,2.521 0.615,0.198 10 false GND 5.677,2.792 6.76,3.177 1.083,0.385 10 false Four Wheel Drive Control ECU 4.677,1.781 5.292,1.979 0.615,0.198 10 false 4WD 2.365,1.885 3.76,2.063 1.396,0.177 10 false from IG1 NO. 3 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK OPEN IN CAN BUS WIRE (FOUR WHEEL DRIVE CONTROL ECU BRANCH WIRE)
2.CHECK OPEN IN CAN BUS WIRE (FOUR WHEEL DRIVE CONTROL ECU BRANCH WIRE)
a.
U148351E03
0.49,1.01 0.573,1.01 0.573,1.01 0.688,1.344 false 0.594,0.719 0.688,0.719 0.688,0.719 0.76,1.365 false 0.052,0 0.219,0.188 0.167,0.188 10 false *a 0.167,0.635 0.594,0.792 0.427,0.156 10 false CANH 0.094,0.927 0.49,1.083 0.396,0.156 10 false CANL 2.417,1.229 2.719,1.385 0.302,0.156 10 false G53

Disconnect the G53 four wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G53-19 (CANH) - G53-20 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Four Wheel Drive Control ECU)



OK

3.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE FOUR WHEEL DRIVE CONTROL ECU BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - BATTERY AND BODY GROUND)
a.
U148350E03
1.771,1.208 1.854,1.208 1.854,1.208 2.052,1.448 false 1.969,0.969 2.063,0.969 2.063,0.969 2.167,1.438 false 0.031,0 0.229,0.208 0.198,0.208 10 false *a 1.396,1.5 1.708,1.667 0.313,0.167 10 false G54 1.792,0.885 1.979,1.052 0.188,0.167 10 false IG 1.438,1.125 1.76,1.292 0.323,0.167 10 false GND

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the G54 four wheel drive control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-4 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G54-3 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Four Wheel Drive Control ECU)


OK

REPLACE 4 WHEEL DRIVE CONTROL ECU NO.2

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR